Matsushita CF-30CTQAZBM service manual Board

Page 24

9.1.3. Removing the HDD

9.1.4. Removing the KB Cover, Hinge Cover L, Hinge Cover R and Key-

HDD FPC

HDD

Heater Sheet

Sheet Sheet

<K1-17>

Heater <K1-17>

Tab

HDD U Case Ass’y

<K1-16>

HDD

Damper

Ass’y

Tab

HDD L

Case Ass’y

board

<N5>		<N5>
		Bluetooth PCB
<N5>		<N5> <N2>
<N5>		<N5> <N2>
	<N5>	Hinge Cover L
	<N5>		<N5>
KB Cover		<N5>	<N5>
KB Cover			<N2>
			<N2>

Hinge

Cover R

1.Remove the Screw. <K1-16>

2.Remove the 4 Screws. <K1-17>

3.Release the 2 Tabs, and remove the HDD U Case Ass'y and the HDD L Case Ass'y.

4.Remove the HDD Dumper Ass'y.

5.Remove the 2 Sheets.

6.Remove the Heater and the Heater Sheet.

7.Remove the HDD FPC.

Screws <K1-16>: DFHE5025XA

Screws <K1-17>: DRQT2+E8FKL

Keyboard

1.Remove the 4 Screws <N5>, and remove the KB Cover.

2.Remove the 2 Screws <N2> and the 4 Screws <N5>, and remove the Hinge Cover L,R.

3.Remove the Keyboard.

Screws <N2>: DRHM5054XA

Screws <N5>: DRQT26+D4FKL

9-2

Image 24

Contents Model No. CF-30CTQAZBM How to replace the fuse For U.K This apparatus must be earthed for your safetyLaser Safety Information Page Page Contents Specifications Model NoAge*20, Recover ProTM 6*20 Only for model with wireless LANOnly for model with Bluetooth You need to install to use the featureNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Error Diagnosis by Checking Beep Signal Sound Beep signal sound Error messageOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility PC-Diagnostic utility End method Content of the setup is returned to the setting of the userSelection of tested device Content of standard test Content of enhancing test Record area frequently accessed All record area is testedTest item Stanard Ty of breakdownContent of Standard Test Content of Extend Test Express Card ConnectorWiring between Super I/O Test ItemWiring Connection Diagram Removing the Battery Pack and HDD Preparation PackBoard Removing the KB Cable Cover and LCD Cable Cover Removing the GPS PCB and Blue- tooth PCBRemoving the Dimm Cover and Bot- tom Cover Removing the USB PCB and AntennaRemoving the FPC HDD BAT Removing the PAD PCBRemoving the Main PCB MP PCB Remove the 4 Screws. N14 PCBRemoving the Handle and Power SW Removing the Display Unit Removing the LCD Rear Cabinet Hinge L and RRemoving the Inverter PCB, TS PCB and LCD Unit Removing the Antenna PCB L and RSetting the Antenna PCB L and R Screws N2 DRHM5054XA Arranging the Antenna L and R CablesSetting the Inverter PCB, TS PCB and LCD Unit Preparation of InverterSetting the LCD Rear Cabinet, Hinge L and R Assembly of LCD UnitSetting the Display Unit Setting the Handle and Power SWAttach the Power LED Packing Sheet to the LED Spacer Fix the SW LED PCB using the Screw. N5Fix the Palm Top Cover using the 5 Screws. N4 No1 to Set the SW LED PCBAssembly of Power SW Assembly of Palm Top CoverSetting the I/O PCB Setting the SD PCB, Express Card Setting the Main PCB Connect the 2 Cables to the 2 Connectors. CN17,CN27Fix the Screw. N7 Attach the TOP Screws Assembly of LAN, Modem and MDC Assembly of Main PCBSetting the PAD PCB Assembly of PAD PCBSetting the FPC HDD BAT Preparation of HDD FPC AssyDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Setting the GPS PCB and Bluetooth PCB Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNLSetting the KB Cable Cover, Keyboard and LCD Cable Cover Arranging the KeyboardSetting the HDD Screws N2 DRHM5054XA Screws N5 DRQT26+D4FKLPreparation oh HDD Assy HDD FPC Ass’yPush and bend HDD Thermal Plate SEC Page Setting the Battery Pack and HDD Pack Set the HDD Pack Set the Battery PackXploded View 18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1CF-30CTQAZBM 10-219 + 0.02 N.m 216 + 0.0196 N.m314 + 0.0196 N.m 441 + 0.049 N.m10-4 45 + 0.50 N.m 10-510-6 10-7 Replacement Parts List Comparison Table