Matsushita CF-30CTQAZBM service manual Setting the KB Cable Cover, Keyboard and LCD Cable Cover

Page 51

9.2.16. Setting the KB Cable Cover, Keyboard and LCD Cable Cover

1.Set the Keyboard onto the Computer.

2.Connect the 2 Cables to the 2 Cables. (CN13,CN14)

3.Fix the KB Cable Cover using the 7 Screws. <N4> No1 to No7

4.Set the LCD Cable Plate.

5.Fix the LCD Cable Cover using the 3 Screws. <N4> No1 to No3

Note:

Tighten the Screws in the numbered order (No1 to No7). Tighten the Screws in the numbered order (No1 to No3).

Screws <N4>: DRQT26+D3FKL

		No.3	No.5
		<N4>	<N4>
	No.4	No.1	No.7
to Connector	No.4	<N4>	<N4>
to Connector	<N4>		No.2
(CN14)			No.2
(CN14)			<N4>
No.6			KB Cable Cover
No.6			No.2
<N4>			No.2
			<N4>
to Connector			LCD
to Connector			Cable Cover
(CN13)			Cable Cover
(CN13)			No.3
			No.3
			<N4>
			No.1
			<N4>

Keyboard	LCD
	LCD
	Cable Plate

Connector

(CN14)

Connector

(CN13)

QArranging the Keyboard

	* Notes:
	1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
	1. Attach the Keyboard US and Keyboard Spacer. (KB Preparation)
	2. Attach the Keyboard Back Plate and Keyboard Spacer Sheet. (Plate Preparation)
Keyboard US is installed	(Ensure Keyboard Spacer Sheet does not run over the level of Keyboard Back Plate.)
	3. Attach the prepared KB to the prepared plate.
	(Insert the KB protrusions into the plate holes and determine the position.)
	Plate hole

Attach the Keyboard

Spacer Tape

Attach the Keyboard

Back Plate

Attach the Keyboard

Spacer Sheet

Attach the Keyboard Fook Spacer Lower : Fit to the edge of plate (KBD back plate).

Both sides should not come over the plate.

9-29

Image 51

Contents Model No. CF-30CTQAZBM For U.K This apparatus must be earthed for your safety How to replace the fuseLaser Safety Information Page Page Contents Model No SpecificationsYou need to install to use the feature Age*20, Recover ProTM 6*20Only for model with wireless LAN Only for model with BluetoothNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Error Diagnosis by Checking Beep Signal Sound Beep signal sound Error messageOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility PC-Diagnostic utility End method Content of the setup is returned to the setting of the userSelection of tested device Ty of breakdown Content of standard test Content of enhancing testRecord area frequently accessed All record area is tested Test item StanardTest Item Content of Standard Test Content of Extend TestExpress Card Connector Wiring between Super I/OWiring Connection Diagram Preparation Pack Removing the Battery Pack and HDDBoard Removing the GPS PCB and Blue- tooth PCB Removing the KB Cable Cover and LCD Cable CoverRemoving the USB PCB and Antenna Removing the Dimm Cover and Bot- tom CoverRemoving the FPC HDD BAT Removing the PAD PCBRemoving the Main PCB MP PCB PCB Remove the 4 Screws. N14Removing the Handle and Power SW Hinge L and R Removing the Display Unit Removing the LCD Rear CabinetRemoving the Antenna PCB L and R Removing the Inverter PCB, TS PCB and LCD UnitScrews N2 DRHM5054XA Arranging the Antenna L and R Cables Setting the Antenna PCB L and RPreparation of Inverter Setting the Inverter PCB, TS PCB and LCD UnitAssembly of LCD Unit Setting the LCD Rear Cabinet, Hinge L and RSetting the Handle and Power SW Setting the Display UnitSet the SW LED PCB Attach the Power LED Packing Sheet to the LED SpacerFix the SW LED PCB using the Screw. N5 Fix the Palm Top Cover using the 5 Screws. N4 No1 toAssembly of Palm Top Cover Assembly of Power SWSetting the I/O PCB Setting the SD PCB, Express Card Connect the 2 Cables to the 2 Connectors. CN17,CN27 Setting the Main PCBFix the Screw. N7 Attach the TOP Screws Assembly of Main PCB Assembly of LAN, Modem and MDCAssembly of PAD PCB Setting the PAD PCBPreparation of HDD FPC Assy Setting the FPC HDD BATDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNL Setting the GPS PCB and Bluetooth PCBArranging the Keyboard Setting the KB Cable Cover, Keyboard and LCD Cable CoverScrews N2 DRHM5054XA Screws N5 DRQT26+D4FKL Setting the HDDHDD FPC Ass’y Preparation oh HDD AssyPush and bend HDD Thermal Plate SEC Page Set the HDD Pack Set the Battery Pack Setting the Battery Pack and HDD Pack18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1 Xploded View10-2 CF-30CTQAZBM441 + 0.049 N.m 19 + 0.02 N.m216 + 0.0196 N.m 314 + 0.0196 N.m10-4 10-5 45 + 0.50 N.m10-6 10-7 Replacement Parts List Comparison Table