Matsushita CF-30CTQAZBM service manual Assembly of USB PCB and Antenna PCB

Page 47

QAssembly of USB PCB and Antenna PCB

* Notes:

1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Safety Working

Attach the Tape

Safety Working

Attach the Antenna Cable Sheet

Order of fixing

Screw Screw

Set on the top.

W-LAN Cable

Connection

EXT Antenna PCB is set

Process the cable from LCD.

Fit to the groove.
Difference : 1 or less			Antenna Cable
Tighten of Screw			Plate is set
Tighten of Screw

Connect the coaxial cable from LCD.

Tighten of

Screw

Along the groove

Tighten of

Screw

Pull W-LAN Cable out to the surface from the hole.

* Notes:

1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Match to the board edge.

Difference: less than 1

Match to the CN edge.

Difference: less than 1

Attach the kapton tape into CD Edge Sheet.

Safety Working

Tighten of Screw	PCB USB Sub is set

Cable USB is set

9-25

Image 47

Contents Model No. CF-30CTQAZBM For U.K This apparatus must be earthed for your safety How to replace the fuseLaser Safety Information Page Page Contents Model No SpecificationsYou need to install to use the feature Age*20, Recover ProTM 6*20Only for model with wireless LAN Only for model with BluetoothNames and Functions of Part E F G Diagram Diagnosis Procedure Troubleshooting Outline of Post Error Diagnosis by Checking Beep Signal SoundBeep signal sound Error message Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device PC-Diagnostic utility End methodContent of the setup is returned to the setting of the user Ty of breakdown Content of standard test Content of enhancing testRecord area frequently accessed All record area is tested Test item StanardTest Item Content of Standard Test Content of Extend TestExpress Card Connector Wiring between Super I/OWiring Connection Diagram Preparation Pack Removing the Battery Pack and HDDBoard Removing the GPS PCB and Blue- tooth PCB Removing the KB Cable Cover and LCD Cable CoverRemoving the USB PCB and Antenna Removing the Dimm Cover and Bot- tom CoverRemoving the Main PCB Removing the FPC HDD BATRemoving the PAD PCB MP PCB PCB Remove the 4 Screws. N14Removing the Handle and Power SW Hinge L and R Removing the Display Unit Removing the LCD Rear CabinetRemoving the Antenna PCB L and R Removing the Inverter PCB, TS PCB and LCD UnitScrews N2 DRHM5054XA Arranging the Antenna L and R Cables Setting the Antenna PCB L and RPreparation of Inverter Setting the Inverter PCB, TS PCB and LCD UnitAssembly of LCD Unit Setting the LCD Rear Cabinet, Hinge L and RSetting the Handle and Power SW Setting the Display UnitSet the SW LED PCB Attach the Power LED Packing Sheet to the LED SpacerFix the SW LED PCB using the Screw. N5 Fix the Palm Top Cover using the 5 Screws. N4 No1 toAssembly of Palm Top Cover Assembly of Power SWSetting the I/O PCB Setting the SD PCB, Express Card Connect the 2 Cables to the 2 Connectors. CN17,CN27 Setting the Main PCBFix the Screw. N7 Attach the TOP Screws Assembly of Main PCB Assembly of LAN, Modem and MDCAssembly of PAD PCB Setting the PAD PCBPreparation of HDD FPC Assy Setting the FPC HDD BATDirection C View Tighten Setting the USB PCB and Antenna PCB Assembly of USB PCB and Antenna PCB Setting the Dimm Cover and Bottom Cover Preparation of Dimm Cover Screws N11 DFHE5025XA Screws N12 DXQT2+F3FNL Setting the GPS PCB and Bluetooth PCBArranging the Keyboard Setting the KB Cable Cover, Keyboard and LCD Cable CoverScrews N2 DRHM5054XA Screws N5 DRQT26+D4FKL Setting the HDDHDD FPC Ass’y Preparation oh HDD AssyPush and bend HDD Thermal Plate SEC Page Set the HDD Pack Set the Battery Pack Setting the Battery Pack and HDD Pack18 + 0.22 N.m + 0.2 kgf.cm 2 + 0.02 N.m 10-1 Xploded View10-2 CF-30CTQAZBM441 + 0.049 N.m 19 + 0.02 N.m216 + 0.0196 N.m 314 + 0.0196 N.m10-4 10-5 45 + 0.50 N.m10-6 10-7 Replacement Parts List Comparison Table