Minolta manual Outline of the CF2002/CF3102 System Setup

Page 2

4. Printer

5. Control Panel

6. Printer Controller/ Interface kit

Printer Panel 1

1. Outline of the CF2002/CF3102 System Setup

These Setup Instructions describe the setup for the parts marked in grey in the flowchart shown below.

When setting up a system consisting of the printer and its various options, perform the setup according to the procedure described below.

1. Copy Table CT-2

NOTE

•Install and setup each option according to the instructions included with the option.

•For information on adjusting the PF-118, PF-121 and AD-14, refer to the section “Adjusting the Options” on pages 27 to 31 of these Setup Instructions.

2-A. Paper Feed Unit PF-118

2-B. Large Capacity Cabinet PF-121

2-C. Copy Desk CD-2M


3-A. Dehumidifying Heater					3-B. Dehumidifying Heater

*: U.S.A and Canada only

4:Printer

Unpack the unit, install it, adjust it using the servicing equipment, and then calibrate the gradation levels with the X-Rite.

5:Control Panel

Attach the control panel to the printer.

6:Printer Controller/Interface Kit

Attach the printer controller, and then specify the necessary settings.

7.Duplex Unit AD-14

8.Data Terminal DT-105*

9.Mechanical Counter


10-A. Finisher FN-8			10-B. Finisher FN-116



11-A. Punch KIT PK-4			11-B. Option tray JS-100

				C4581U019AA

4581-7777-01

– 1 –

Image 2

Contents Printer Panel Outline of the CF2002/CF3102 System Setup Precautions Concerning the Package Contents Manuals Precautions Concerning the Installation of the ControllerUnpacking the Printer Unpacking the AccessoriesUnpacking Removing the Protective Tape and Packing Materials Installing the Unit Installing the Imaging Unit4025U027AA Installing the Toner Cartridge and the Filter Affixing the Label Installing the Manual Holder Affix the label that corresponds with the installed optionsConnecting the Cables Loading Test Paper Setting Up the Servicing EquipmentCalibrating the Printer Setting Up the Selector Connecting the Equipment CablesRite Calibration If the selector is being used, set the selector knob to B C4004P575CA C4004U576AA C4004P580CA C4004P582CA C4004P590CA Click Fin. Time 4581-7777-01 Making System Setting Checking the Date SettingSpecifying the Serial Number Specifying Who Performs Replacements Printing the List To set the Energy Save Mode parameter To set the Sleep Mode parameter Select 2/2 Click Energy SaverSelect 2/2 Click Sleep Loading Paper TraySlide the lateral guides against the edges of the paper C4004U141AA Adjusting the Options Checking the Paper Reference Position for PF-118Measure margin a from the edge Print another test page and check the paper Click Dup. Left Margin Do not measure from the back of the test pat- tern Specifying the Administrator Access Code Preparing for Installation of the ControllerSelecting the Printer Setting Specifying the Peripheral SettingInstall the Printer Panel for the Internal Controller Installing the Printer PanelChecking the Contents of the Printer Panel Be careful not to disconnect other connectors accidentally Close the front door Operating Environment Installing the Printer ControllerOutline of Setup Checking the Contents of the Enclosed Interface Kit Connect the three connectors Connect the controller power cord to the printer C4581U013AA C4581U026AA Specifying the Printer Controller Settings Checking With a Test Print LED descriptionsObjective Installing the Patch FilesPatch file installation procedure To turn off the printer controller Specifying User’s Choice Settings Entering Setup Mode on the ControllerCommon Settings for Controllers Settings Required for a Local Connection IEEE1284 CentronicsNetwork Printing on a Computer Running Windows SMB printingLPD LPR printing IPP printingNetWare environment Settings for NetWare printing Network Printing on a Macintosh Computer AppleTalk printingPerforming a test print from client PC Checking Operation After Specifying SettingsInstallation Troubleshooting

Related manuals

Manual 212 pages 52.15 Kb

Manual 156 pages 52.37 Kb