Minolta CF3102, CF2002 Checking Operation After Specifying Settings, Installation Troubleshooting

Page 51

Printer Panel 1

20. Checking Operation After Specifying Settings

After the setup procedures for the controller and user environment are finished, check the operation to ensure that the setup has been performed correctly.

Performing a test print from client PC

This operation is performed to check if the settings for the connection with the computer are correct.

1.In the windows displayed by clicking the Start button, pointing to [Settings], then click- ing [Printers], right-click the printer, and then click [Properties].

2.Click the General tab, and then click [Print Test Page].

If the test page cannot be printed, refer to [Installation Troubleshooting].

21. Installation Troubleshooting

When printing cannot be carried out over a network:

	Check			Possible Cause	Action

1	Does the print job	Yes		A printer error (out of	Correct the cause of the
	appear in the touch			paper, out of toner, etc.)	error.
	panel of the copier?			occurred.

		No		The data has not yet	Go to 2.
				been received.

2	Is there a response	Yes		The print destination port	Specify the correct port.
	from pinging sent			setting is incorrect.
	from the computer
	from the computer			The computer is tempo-	Restart the computer.
	to the controller?			The computer is tempo-	Restart the computer.
	to the controller?			rarily malfunctioning.
				rarily malfunctioning.

				The printer driver is not	Follow the procedure to
				installed correctly.	correctly uninstall, then
					re-install the printer
					driver.

		No		The controller circuit	Restart the controller.
				board is temporarily mal-
				functioning.

				The network cable is dis-	Correctly connect the
				connected or the relay	cable, or restart or
				device is faulty.	replace the relay device.

				The IP address and/or	Specify the correct IP
				subnet mask is incor-	address and subnet
				rectly specified.	mask.

4581-7777-01

– 50 –

Image 51

Contents Printer Panel Outline of the CF2002/CF3102 System Setup Precautions Concerning the Installation of the Controller Precautions Concerning the Package Contents ManualsUnpacking the Accessories UnpackingUnpacking the Printer Removing the Protective Tape and Packing Materials Installing the Imaging Unit Installing the Unit4025U027AA Installing the Toner Cartridge and the Filter Affix the label that corresponds with the installed options Affixing the Label Installing the Manual HolderConnecting the Cables Setting Up the Servicing Equipment Calibrating the PrinterLoading Test Paper Connecting the Equipment Cables Setting Up the SelectorRite Calibration If the selector is being used, set the selector knob to B C4004P575CA C4004U576AA C4004P580CA C4004P582CA C4004P590CA Click Fin. Time 4581-7777-01 Checking the Date Setting Making System SettingSpecifying the Serial Number Specifying Who Performs Replacements Printing the List To set the Energy Save Mode parameter Select 2/2 Click Energy Saver To set the Sleep Mode parameterSelect 2/2 Click Sleep Tray Loading PaperSlide the lateral guides against the edges of the paper C4004U141AA Checking the Paper Reference Position for PF-118 Adjusting the OptionsMeasure margin a from the edge Print another test page and check the paper Click Dup. Left Margin Do not measure from the back of the test pat- tern Specifying the Peripheral Setting Preparing for Installation of the ControllerSelecting the Printer Setting Specifying the Administrator Access CodeInstalling the Printer Panel Checking the Contents of the Printer PanelInstall the Printer Panel for the Internal Controller Be careful not to disconnect other connectors accidentally Close the front door Installing the Printer Controller Outline of SetupOperating Environment Checking the Contents of the Enclosed Interface Kit Connect the three connectors Connect the controller power cord to the printer C4581U013AA C4581U026AA Specifying the Printer Controller Settings LED descriptions Checking With a Test PrintInstalling the Patch Files Patch file installation procedureObjective To turn off the printer controller Entering Setup Mode on the Controller Specifying User’s Choice SettingsSettings Required for a Local Connection IEEE1284 Centronics Common Settings for ControllersSMB printing Network Printing on a Computer Running WindowsIPP printing LPD LPR printingNetwork Printing on a Macintosh Computer AppleTalk printing NetWare environment Settings for NetWare printingChecking Operation After Specifying Settings Installation TroubleshootingPerforming a test print from client PC

Related manuals

Manual 212 pages 52.15 Kb

Manual 156 pages 52.37 Kb