Unitech MS860 manual Charging the Scanner, How to determine if the scanner needs recharging

Page 10

INTRODUCTION

CHARGING THE SCANNER:

Prior to performing any operation with the scanner, make sure it has been fully charged.

How to determine if the scanner needs recharging:

1.During operation, a flashing red scanner LED indicates the scanner has low power.

2.When the trigger is pressed and a scan laser line is not visible (do NOT look directly into the scanner), the scanner has no power. Make sure the scanner is not merely switched off.

To charge the scanner, place the unit into the cradle. The battery status LED on the cradle will glow red, indicating the charging process has begun.

To Charge the MS860:

Simply place the MS860 into the MS086 Charging Cradle. Make sure the MS086 Cradle is plugged into an available electrical outlet via its Power Supply.

A complete charging process takes about 4 to 5 hours, during which the cradle’s battery charging LED will glow red. After charging is complete the battery charging LED will remain a steady green. When charging the scanner for the first time, make sure the scanner remains on the cradle until after the battery charging LED changes from red to green.

Manufacturer’s Suggestion:

If the scanner is not to be used for a long period of time, it is recom- mended that you turn off the battery power of the scanner. Use an unfolded paper clip to push down the internal power on/off switch, located inside the round hole on the yellow laser warning label of the scanner (see page 5). You will feel a ‘click’ when the internal switch is moved up to the “OFF” position or when the internal switch is moved down to the “ON” position.

To ensure that the scanner has been switched off, press the scanner’s trigger and make sure that the scanner’s LED does not glow red.

MS860 WiFi Manual

8

Image 10

Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner Parts Scanner LEDBuzzer Cradle Parts Cradle LEDsHow to determine if the scanner needs recharging Charging the ScannerNetwork Settings Modifying the WiFi settings Glossary IP AddressWEP Network Settings Using SCM for Scanner Network SettingNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Intercharacter Delay Beeps and DelaysInterblock Delay Keyboard WedgeLanguage Function CodeCaps-Lock Use Numeric KeypadData Bit Baud RateParity HandshakingTime Out RS232BCC Character Data DirectionScanner Port TerminatorUse Code ID Double VerificationSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Scanning Mode Label TypePreamble Aim Function for Long Range EngineAiming Time for Long Range Engine PostambleBar Code Symbologies CodeInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code Codabar UPC-AUPC-E EAN-13EAN-8 Delta CodeSupplement Code for UPC-E, ISBN, EAN-13 Label Code IVQualifier Data EditingModifier Scanner Configuration Manager Arrange Formulas Everything Else FormulaProgramming VIA Scanner Input IntroductionQuick Setup Bar Codes BeepUPC-E Beep Tone see page 40 0 None Interblock DelayIntercharacter Delay MediumKeyboard Interface Parity Baud Rate9600 NoneSecond Data Direction for terminal wedge see Send to HostCode ID TerminatorEnter Define Code IDTrigger Scanning ModeDouble Verification Label TypePpoo Check Digit Not Calculate Symbologies GroupCode 39 see Interleaved 2 of 5 ITF seeTelepen Standard 2 China Postal Code Toshiba CodeCode 32 Italian Pharmacy see UCC/EAN 128 seeDefine a Separator for Double Labels Define the EAN 128 Fields SeparatorDefine Minimum and Maximum Length No Send Check Digit Double Module Code 128 seeMSI / Plessey Code Code 93 seeNo Send Code 11 Special seeCodabar see Label Code IV and V seeExit EAN-13 see EAN-8Off / On Supplement Code seeDelta Distance Code see Qualifiers Modifiers Special CharactersFormula Format Code TypeSpecial Characters in this section TCP/IP Function Codes for PC Ascii Chart Characters in parentheses represent Extended Code= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Troubleshooting Generic Scanner Troubleshooting TipsProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char