Unitech MS860 manual Network Settings

Page 32

NETWORK SETTINGS

5. Define the RS232 settings according to page 88, RS232 Default Step 8: If “Yes” was selected in Step 7, fill in

Settings, click “OK”

the WEP parameters and type a passwork in the Key 1 field. Click “Next”.

Step 9: Select “Yes” or “No” for Power

Saving Mode.

6.Press the scan button to scan the barcode. Step 10: Verify the information is correct.

Click “Back” to modify the configura-

tion if necessary.

Click “Next” when finished.

Step 11: Setup is complete.

Step 12: Select an appropriate printer to produce a setup sheet containing bar codes. Use your MS860 scanner to scan the barcodes on the sheet sequentially to configure the scanner.

30	MS860 WiFi Manual

Image 32

Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner Parts Scanner LEDBuzzer Cradle Parts Cradle LEDsHow to determine if the scanner needs recharging Charging the ScannerNetwork Settings Modifying the WiFi settings Glossary IP AddressWEP Network Settings Using SCM for Scanner Network SettingNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Beeps and Delays Interblock DelayIntercharacter Delay Keyboard WedgeFunction Code Caps-LockLanguage Use Numeric KeypadBaud Rate ParityData Bit HandshakingRS232 BCC CharacterTime Out Data DirectionScanner Port TerminatorUse Code ID Double VerificationSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Scanning Mode Label TypeAim Function for Long Range Engine Aiming Time for Long Range EnginePreamble PostambleBar Code Symbologies CodeInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code Codabar UPC-AUPC-E EAN-13EAN-8 Delta CodeSupplement Code for UPC-E, ISBN, EAN-13 Label Code IVModifier Data EditingQualifier Scanner Configuration Manager Arrange Formulas Everything Else FormulaProgramming VIA Scanner Input IntroductionQuick Setup Bar Codes BeepUPC-E Interblock Delay Intercharacter DelayBeep Tone see page 40 0 None MediumKeyboard Interface Baud Rate 9600Parity NoneSecond Data Direction for terminal wedge see Send to HostTerminator EnterCode ID Define Code IDScanning Mode Double VerificationTrigger Label TypePpoo Symbologies Group Code 39 seeCheck Digit Not Calculate Interleaved 2 of 5 ITF seeStandard 2 China Postal Code Toshiba Code Code 32 Italian Pharmacy seeTelepen UCC/EAN 128 seeDefine Minimum and Maximum Length Define the EAN 128 Fields SeparatorDefine a Separator for Double Labels Code 128 see MSI / Plessey CodeNo Send Check Digit Double Module Code 93 seeCode 11 Special see Codabar seeNo Send Label Code IV and V seeExit EAN-13 see EAN-8Delta Distance Code see Supplement Code seeOff / On Qualifiers Modifiers Special CharactersSpecial Characters in this section Code TypeFormula Format TCP/IP Function Codes for PC Ascii Chart Characters in parentheses represent Extended Code= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Troubleshooting Generic Scanner Troubleshooting TipsProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char