Unitech MS860 manual Modifiers, Special Characters

Page 81

PROGRAMMING VIA SCANNER INPUT

Data Editing, continued

Note: Once a Qualifier is specified, other bar codes that do not meet the requirements of the Qualifier will be disregarded.

If you would like bar codes not specified by the Qualifier to output normally, simply add another qualifier that specifies all bar codes (19), starting at position 1, and outputting all remaining (#). (See example at the bottom of this page.)

Modifiers:

Original Data - Part or all of the original data string can be selected. The programming bar codes must be entered in the following sequence: O-STR,P,N,- where “O-STR” announces that the next bar code inputs refer to where the output should begin and how many characters should be output. For example, if 7 characters are to be output beginning with the 4th character, the bar code scanning sequence should be “O-STR, 4,7,”. If we want all the characters after the 4th character to be output, the sequence should be “O-STR,4,#,”, with the “#” character signifying that the entire string (after the 4th character) should be output. Should you decide that the last two characters should not be output, the sequence would be “”O-STR,4,#-2,”, with the “#-2” specifying all remaining minus 2.

Special Characters

,Comma - Used as a separator between formula parameters, beginning with the IN_ID parameter and ending with the Enter parameter.

“Quotation Mark - Used to begin and end a character string. A character string bounded by quotation marks is treated as a single unit, and would be written as “abcd”.

* Asterisk - Wild-card character used to specify any digit or position.

# Hash sign - Wild-card character used to specify any letter or last position.

Finally, end the programming sequence with the “Enter” bar code. Do not follow it with a comma. If you need to add another formula, do so now by scanning the “IN_ID” bar code directly, followed by the rest of the second formula’s parameters, and then “Enter” again. Lastly, scan the “Exit” bar code.

Thus, if we want to output just the first five characters only from UPC-A input and then follow it with three “0”s, the scanning sequence should be as follows:

Enter Group 9 IN_ID , 3 , O-STR , 1 , 5 , “ 0 0 0 “ , Enter Exit

If we only want to treat UPC-A this way, but still want other symbologies to output normally, the scanning sequence would be as follows:

Enter Group 9 IN_ID , 3 , O-STR , 1 , 5 , “ 0 0 0 “ , Enter

IN_ID , 19 , O-STR , 1 , # , Enter Exit

79

MS860 WiFi Manual

Page 80 Page 82
Image 81
Page 80 Page 82
Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner LED Scanner PartsBuzzer Cradle LEDs Cradle PartsCharging the Scanner How to determine if the scanner needs rechargingNetwork Settings Modifying the WiFi settings IP Address GlossaryWEP Using SCM for Scanner Network Setting Network SettingsNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Interblock Delay Beeps and DelaysIntercharacter Delay Keyboard WedgeCaps-Lock Function CodeLanguage Use Numeric KeypadParity Baud RateData Bit HandshakingBCC Character RS232Time Out Data DirectionTerminator Scanner PortDouble Verification Use Code IDSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Label Type Scanning ModeAiming Time for Long Range Engine Aim Function for Long Range EnginePreamble PostambleCode Bar Code SymbologiesInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code UPC-A CodabarEAN-13 UPC-EDelta Code EAN-8Label Code IV Supplement Code for UPC-E, ISBN, EAN-13Data Editing QualifierModifier Scanner Configuration Manager Everything Else Formula Arrange FormulasIntroduction Programming VIA Scanner InputBeep Quick Setup Bar CodesUPC-E Intercharacter Delay Interblock DelayBeep Tone see page 40 0 None MediumKeyboard Interface 9600 Baud RateParity NoneData Direction for terminal wedge see Send to Host SecondEnter TerminatorCode ID Define Code IDDouble Verification Scanning ModeTrigger Label TypePpoo Code 39 see Symbologies GroupCheck Digit Not Calculate Interleaved 2 of 5 ITF seeCode 32 Italian Pharmacy see Standard 2 China Postal Code Toshiba CodeTelepen UCC/EAN 128 seeDefine the EAN 128 Fields Separator Define a Separator for Double LabelsDefine Minimum and Maximum Length MSI / Plessey Code Code 128 seeNo Send Check Digit Double Module Code 93 seeCodabar see Code 11 Special seeNo Send Label Code IV and V seeExit EAN-8 EAN-13 seeSupplement Code see Off / OnDelta Distance Code see Qualifiers Special Characters ModifiersCode Type Formula FormatSpecial Characters in this section TCP/IP Function Codes for PC Characters in parentheses represent Extended Code Ascii Chart= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Generic Scanner Troubleshooting Tips TroubleshootingProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char
Top Page Image Contents