Unitech MS860 manual Interleaved 2

Page 51

SCANNER CONFIGURATION MANAGER

Bar Code Symbologies, continued

Interleaved 2 of 5

zEnabled toggles the ability for the scanner to read I 2 of 5 on or off. Default is “Yes”.

zCode ID is a user-definable identification letter for I 2 of 5, which is referred to in the “Use Code ID” function on page 45.

Default is letter “I”.

zFix Length (by first 3 reads) fixes the length of acceptable subse- quent bar code reads from the first three bar codes read. Useful as a data verification if all bar codes are of a consistent length.

Default is “No”.

zCheck Digit defines whether or not a check digit (to insure data accuracy) is calculated, and if so, whether it should be sent or not. Default is “Not Calculate”.

zSupress Digit suppresses the output of the first or last bar code digit. Default is “Not Suppressed”.

zMinimum Length defines the minimum length the user will accept for a valid bar code.

Default is “10”.

zMaximum Length defines the maximum length the user will accept for a valid bar code.

Default is “64”.

49	MS860 WiFi Manual

Image 51

Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner LED Scanner PartsBuzzer Cradle LEDs Cradle PartsCharging the Scanner How to determine if the scanner needs rechargingNetwork Settings Modifying the WiFi settings IP Address GlossaryWEP Using SCM for Scanner Network Setting Network SettingsNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Keyboard Wedge Beeps and DelaysInterblock Delay Intercharacter DelayUse Numeric Keypad Function CodeCaps-Lock LanguageHandshaking Baud RateParity Data BitData Direction RS232BCC Character Time OutTerminator Scanner PortDouble Verification Use Code IDSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Label Type Scanning ModePostamble Aim Function for Long Range EngineAiming Time for Long Range Engine PreambleCode Bar Code SymbologiesInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code UPC-A CodabarEAN-13 UPC-EDelta Code EAN-8Label Code IV Supplement Code for UPC-E, ISBN, EAN-13Data Editing QualifierModifier Scanner Configuration Manager Everything Else Formula Arrange FormulasIntroduction Programming VIA Scanner InputBeep Quick Setup Bar CodesUPC-E Medium Interblock DelayIntercharacter Delay Beep Tone see page 40 0 NoneKeyboard Interface None Baud Rate9600 ParityData Direction for terminal wedge see Send to Host SecondDefine Code ID TerminatorEnter Code IDLabel Type Scanning ModeDouble Verification TriggerPpoo Interleaved 2 of 5 ITF see Symbologies GroupCode 39 see Check Digit Not CalculateUCC/EAN 128 see Standard 2 China Postal Code Toshiba CodeCode 32 Italian Pharmacy see TelepenDefine the EAN 128 Fields Separator Define a Separator for Double LabelsDefine Minimum and Maximum Length Code 93 see Code 128 seeMSI / Plessey Code No Send Check Digit Double ModuleLabel Code IV and V see Code 11 Special seeCodabar see No SendExit EAN-8 EAN-13 seeSupplement Code see Off / OnDelta Distance Code see Qualifiers Special Characters ModifiersCode Type Formula FormatSpecial Characters in this section TCP/IP Function Codes for PC Characters in parentheses represent Extended Code Ascii Chart= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Generic Scanner Troubleshooting Tips TroubleshootingProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char