Unitech MS860 manual Mechanical

Page 90

SPECIFICATIONS

MECHANICAL
Scanner Dimensions:	Length - 5” (126mm)
	Width = 3.25” (83mm)
	Height = 5.625” (143mm)
Cradle Dimensions:	Length - 8.125” (206mm)
	Width = 3.8125” (97mm)
	Height = 2.25” (57mm)
Scanner Weight:	11 oz. (312 grams)
Cradle Weight:	14.5 oz. (410 grams)
ENVIRONMENTAL
Temperature:	Operating: 32° to 122° F (0° to 50° C)
	Storage: -4° to 140° F (-20° to 60° C)
Humidity:	5% to 95% RH non-condensing
Mechanical Shock:	5 foot (1.5M) drop to concrete
ESD Protection:	8K Contact and 12K Air
COMMUNICATION
Radio Frequency:	2.4GHz compliant 802.11b protocol
Scalability:	Point to point, multi point
Range:	30M line of sight
WLAN Default Settings:

	Item		Default Setting
	IP Address		192.168.1.250
	IP Subnet Mask		255.255.255.0
	Gateway IP Address		192.168.1.254
	SSID		Wlandemo
	RF Channel		6
	WEP		Disabled
RS232 Default Settings:	Authentication Type		Auto
RS232 Default Settings:

	Item		Default Setting
	Baud Rate		38400
	Data Length		8 (fixed)
	Parity		None (fixed)
	Stop Bit		1 (fixed)
	Flow Control		None

MS860 WiFi Manual

88

Image 90

Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner Parts Scanner LEDBuzzer Cradle Parts Cradle LEDsHow to determine if the scanner needs recharging Charging the ScannerNetwork Settings Modifying the WiFi settings Glossary IP AddressWEP Network Settings Using SCM for Scanner Network SettingNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Intercharacter Delay Beeps and DelaysInterblock Delay Keyboard WedgeLanguage Function CodeCaps-Lock Use Numeric KeypadData Bit Baud RateParity HandshakingTime Out RS232BCC Character Data DirectionScanner Port TerminatorUse Code ID Double VerificationSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Scanning Mode Label TypePreamble Aim Function for Long Range EngineAiming Time for Long Range Engine PostambleBar Code Symbologies CodeInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code Codabar UPC-AUPC-E EAN-13EAN-8 Delta CodeSupplement Code for UPC-E, ISBN, EAN-13 Label Code IVData Editing QualifierModifier Scanner Configuration Manager Arrange Formulas Everything Else FormulaProgramming VIA Scanner Input IntroductionQuick Setup Bar Codes BeepUPC-E Beep Tone see page 40 0 None Interblock DelayIntercharacter Delay MediumKeyboard Interface Parity Baud Rate9600 NoneSecond Data Direction for terminal wedge see Send to HostCode ID TerminatorEnter Define Code IDTrigger Scanning ModeDouble Verification Label TypePpoo Check Digit Not Calculate Symbologies GroupCode 39 see Interleaved 2 of 5 ITF seeTelepen Standard 2 China Postal Code Toshiba CodeCode 32 Italian Pharmacy see UCC/EAN 128 seeDefine the EAN 128 Fields Separator Define a Separator for Double LabelsDefine Minimum and Maximum Length No Send Check Digit Double Module Code 128 seeMSI / Plessey Code Code 93 seeNo Send Code 11 Special seeCodabar see Label Code IV and V seeExit EAN-13 see EAN-8Supplement Code see Off / OnDelta Distance Code see Qualifiers Modifiers Special CharactersCode Type Formula FormatSpecial Characters in this section TCP/IP Function Codes for PC Ascii Chart Characters in parentheses represent Extended Code= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Troubleshooting Generic Scanner Troubleshooting TipsProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char