Unitech MS860 manual Scanner Port, Terminator

Page 40

SCANNER CONFIGURATION MANAGER

Step 9: Select “YES” for using power saving mode. Click “Next”.

Scanner Port

Scanner Port parameters refer to scanner functions (such as Double Verification, Scanning Mode, etc.) and some simple data editing features. For more powerful data editing, refer to the Data Editing section starting on page 44.

Terminator

The Terminator is a command that follows the input of bar code data. Four different terminators can be selected here:

“Enter”

“Return (on numeric keypad)” “Field Exit or Right Control” “None”

AlternativeStep 10: Pleaseterminatorsverify(suchif the asinformationTab) can isbecorrect,configuredclickvia“Next”the . Postamble function (see page 34).

Default is “Enter”.

MS860 WiFi Manual

38

Image 40

Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner Parts Scanner LEDBuzzer Cradle Parts Cradle LEDsHow to determine if the scanner needs recharging Charging the ScannerNetwork Settings Modifying the WiFi settings Glossary IP AddressWEP Network Settings Using SCM for Scanner Network SettingNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Beeps and Delays Interblock DelayIntercharacter Delay Keyboard WedgeFunction Code Caps-LockLanguage Use Numeric KeypadBaud Rate ParityData Bit HandshakingRS232 BCC CharacterTime Out Data DirectionScanner Port TerminatorUse Code ID Double VerificationSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Scanning Mode Label TypeAim Function for Long Range Engine Aiming Time for Long Range EnginePreamble PostambleBar Code Symbologies CodeInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code Codabar UPC-AUPC-E EAN-13EAN-8 Delta CodeSupplement Code for UPC-E, ISBN, EAN-13 Label Code IVQualifier Data EditingModifier Scanner Configuration Manager Arrange Formulas Everything Else FormulaProgramming VIA Scanner Input IntroductionQuick Setup Bar Codes BeepUPC-E Interblock Delay Intercharacter DelayBeep Tone see page 40 0 None MediumKeyboard Interface Baud Rate 9600Parity NoneSecond Data Direction for terminal wedge see Send to HostTerminator EnterCode ID Define Code IDScanning Mode Double VerificationTrigger Label TypePpoo Symbologies Group Code 39 seeCheck Digit Not Calculate Interleaved 2 of 5 ITF seeStandard 2 China Postal Code Toshiba Code Code 32 Italian Pharmacy seeTelepen UCC/EAN 128 seeDefine a Separator for Double Labels Define the EAN 128 Fields SeparatorDefine Minimum and Maximum Length Code 128 see MSI / Plessey CodeNo Send Check Digit Double Module Code 93 seeCode 11 Special see Codabar seeNo Send Label Code IV and V seeExit EAN-13 see EAN-8Off / On Supplement Code seeDelta Distance Code see Qualifiers Modifiers Special CharactersFormula Format Code TypeSpecial Characters in this section TCP/IP Function Codes for PC Ascii Chart Characters in parentheses represent Extended Code= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Troubleshooting Generic Scanner Troubleshooting TipsProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char