Unitech MS860 manual Upc-E, EAN-13

Page 56

SCANNER CONFIGURATION MANAGER

Bar Code Symbologies, continued

UPC-E

zEnabled toggles the ability for the scanner to read UPC-E on or off. Default is “Yes”.

zCode ID is a user-definable identification letter for UPC-E, which is referred to in the “Use Code ID” function on page 45.

Default is letter “E”.

zSend Leading Digit toggles sending or not sending a leading (‘start bar code’) digit.

Default is “Send”.

zSend Check Digit toggles sending or not sending a check digit. Default is “Send”.

zZero Expansion adds 0s to the bar code output to change the UPC-E output format (8 digits) to UPC-A format (12 digits). Default is “No”.

zEnable NSC=1 allows the output of a UPC-E bar code containing a first digit (Number System Character) of “1”.

Default is “No”.

EAN-13

zEnabled toggles the ability for the scanner to read EAN-13 on or off. Default is “Yes”.

zCode ID is a user-definable identification letter for EAN-13, which is referred to in the “Use Code ID” function on page 45.

Default is letter “F”.

zSend Leading Digit toggles sending or not sending a leading (‘start bar code’) digit.

Default is “Send”.

zSend Check Digit toggles sending or not sending a check digit. Default is “Send”.

zBookland EAN toggles whether or not to send the EAN-13 bar code data in Bookland EAN (ISBN) format.

Default is “No”.

MS860 WiFi Manual

54

Image 56

Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner Parts Scanner LEDBuzzer Cradle Parts Cradle LEDsHow to determine if the scanner needs recharging Charging the ScannerNetwork Settings Modifying the WiFi settings Glossary IP AddressWEP Network Settings Using SCM for Scanner Network SettingNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Beeps and Delays Interblock DelayIntercharacter Delay Keyboard WedgeFunction Code Caps-LockLanguage Use Numeric KeypadBaud Rate ParityData Bit HandshakingRS232 BCC CharacterTime Out Data DirectionScanner Port TerminatorUse Code ID Double VerificationSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Scanning Mode Label TypeAim Function for Long Range Engine Aiming Time for Long Range EnginePreamble PostambleBar Code Symbologies CodeInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code Codabar UPC-AUPC-E EAN-13EAN-8 Delta CodeSupplement Code for UPC-E, ISBN, EAN-13 Label Code IVModifier Data EditingQualifier Scanner Configuration Manager Arrange Formulas Everything Else FormulaProgramming VIA Scanner Input IntroductionQuick Setup Bar Codes BeepUPC-E Interblock Delay Intercharacter DelayBeep Tone see page 40 0 None MediumKeyboard Interface Baud Rate 9600Parity NoneSecond Data Direction for terminal wedge see Send to HostTerminator EnterCode ID Define Code IDScanning Mode Double VerificationTrigger Label TypePpoo Symbologies Group Code 39 seeCheck Digit Not Calculate Interleaved 2 of 5 ITF seeStandard 2 China Postal Code Toshiba Code Code 32 Italian Pharmacy seeTelepen UCC/EAN 128 seeDefine Minimum and Maximum Length Define the EAN 128 Fields SeparatorDefine a Separator for Double Labels Code 128 see MSI / Plessey CodeNo Send Check Digit Double Module Code 93 seeCode 11 Special see Codabar seeNo Send Label Code IV and V seeExit EAN-13 see EAN-8Delta Distance Code see Supplement Code seeOff / On Qualifiers Modifiers Special CharactersSpecial Characters in this section Code TypeFormula Format TCP/IP Function Codes for PC Ascii Chart Characters in parentheses represent Extended Code= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Troubleshooting Generic Scanner Troubleshooting TipsProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char