Unitech MS860 manual Code, Ean

Page 53

SCANNER CONFIGURATION MANAGER

Bar Code Symbologies, continued

Code 32

zEnabled toggles the ability for the scanner to read Code 32 on or off. Default is “No”.

zCode ID is a user-definable identification letter for Code 32, which is referred to in the “Use Code ID” function on page 45.

Default is letter “T”.

zSend Leading Character toggles sending or not sending a leading (‘start bar code’) character.

Default is “Send”.

zSend Tailing Character toggles sending or not sending a tailing (‘stop bar code’) character.

Default is “Send”.

EAN 128

zEnabled toggles the ability for the scanner to read EAN 128 on or off.

Default is “No”.

zCode ID is a user-definable identification letter for EAN 128, which is referred to in the “Use Code ID” function on page 45.

Default is letter “None”.

zEnable Code ID determines whether or not to assign a Code ID. Default is “No”.

zField Separator is a user-definable character to insert between fields.

Default is “None”.

Code 128

zEnabled toggles the ability for the scanner to read Code 128 on or off.

Default is “No”.

zCode ID is a user-definable identification letter for Code 128, which is referred to in the “Use Code ID” function on page 45.

Default is letter “None”.

zMinimum Length defines the minimum length the user will accept for a valid bar code.

Default is “1”.

zMaximum Length defines the maximum length the user will accept for a valid bar code.

Default is “64”.

51	MS860 WiFi Manual

Image 53

Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner LED Scanner PartsBuzzer Cradle LEDs Cradle PartsCharging the Scanner How to determine if the scanner needs rechargingNetwork Settings Modifying the WiFi settings IP Address GlossaryWEP Using SCM for Scanner Network Setting Network SettingsNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Interblock Delay Beeps and DelaysIntercharacter Delay Keyboard WedgeCaps-Lock Function CodeLanguage Use Numeric KeypadParity Baud RateData Bit HandshakingBCC Character RS232Time Out Data DirectionTerminator Scanner PortDouble Verification Use Code IDSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Label Type Scanning ModeAiming Time for Long Range Engine Aim Function for Long Range EnginePreamble PostambleCode Bar Code SymbologiesInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code UPC-A CodabarEAN-13 UPC-EDelta Code EAN-8Label Code IV Supplement Code for UPC-E, ISBN, EAN-13Modifier Data EditingQualifier Scanner Configuration Manager Everything Else Formula Arrange FormulasIntroduction Programming VIA Scanner InputBeep Quick Setup Bar CodesUPC-E Intercharacter Delay Interblock DelayBeep Tone see page 40 0 None MediumKeyboard Interface 9600 Baud RateParity NoneData Direction for terminal wedge see Send to Host SecondEnter TerminatorCode ID Define Code IDDouble Verification Scanning ModeTrigger Label TypePpoo Code 39 see Symbologies GroupCheck Digit Not Calculate Interleaved 2 of 5 ITF seeCode 32 Italian Pharmacy see Standard 2 China Postal Code Toshiba CodeTelepen UCC/EAN 128 seeDefine Minimum and Maximum Length Define the EAN 128 Fields SeparatorDefine a Separator for Double Labels MSI / Plessey Code Code 128 seeNo Send Check Digit Double Module Code 93 seeCodabar see Code 11 Special seeNo Send Label Code IV and V seeExit EAN-8 EAN-13 seeDelta Distance Code see Supplement Code seeOff / On Qualifiers Special Characters ModifiersSpecial Characters in this section Code TypeFormula Format TCP/IP Function Codes for PC Characters in parentheses represent Extended Code Ascii Chart= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Generic Scanner Troubleshooting Tips TroubleshootingProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char