Unitech MS860 manual Use Code ID, Double Verification

Page 41

SCANNER CONFIGURATION MANAGER

Step 11: You will see the screen for finished Wi-Fi Setup wizard

Scanner Port, continued

	Use Code ID	Codabar	N
	The Code ID function can be used to	Code 11 / Telpen	J
	identify the type of bar code that is being	Code 32	T
	scanned by inserting an identifying letter	Code 39	M
	(refer to the chart at right) at the begin-	Code 39	M
	(refer to the chart at right) at the begin-	Code 93	L
	ning of the bar code input.	Code 93	L
	ning of the bar code input.	Code 128	K
	For example: if the Code ID function is	Code 128	K
	For example: if the Code ID function is	Delta Code	D
	on, and a bar code string of “54321” was	Delta Code	D
	on, and a bar code string of “54321” was	EAN-8	FF
	output as “M54321”, the bar code would	EAN-8	FF
	thus be identified as type Code 39.	EAN-13	F
	Default is “No”.	I 2 of 5	I
		Label Code IV or V	B
		MSI	O
	Step 12: Click “Finish” will allow you to print out a setup sheet,		P
		Plessey Code	P
	please scan the barcode labels on it to configure your scanner.		H
		S 2 of 5	H
		Toshiba Code	C
		UCC / EAN 128	]C1
		UPC-A	A
		UPC-E	E

Double Verification

Double Verification enables the MS860 to verify the accuracy of the output by outputting only after a specified number (from 0 to 7) of identical results. For instance, if 3 is selected, the MS860 will not output the bar code data until it’s obtained 4 identical scan results (the original scan plus 3 verifying scans).

Because the MS860 normally scans at a rate of 33 scans per second, this process should take less than a fraction of a second, even for higher values, for good quality bar code labels.

Default is “0-Off”.

39	MS860 WiFi Manual

Image 41

Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner LED Scanner PartsBuzzer Cradle LEDs Cradle PartsCharging the Scanner How to determine if the scanner needs rechargingNetwork Settings Modifying the WiFi settings IP Address GlossaryWEP Using SCM for Scanner Network Setting Network SettingsNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Interblock Delay Beeps and DelaysIntercharacter Delay Keyboard WedgeCaps-Lock Function CodeLanguage Use Numeric KeypadParity Baud RateData Bit HandshakingBCC Character RS232Time Out Data DirectionTerminator Scanner PortDouble Verification Use Code IDSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Label Type Scanning ModeAiming Time for Long Range Engine Aim Function for Long Range EnginePreamble PostambleCode Bar Code SymbologiesInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code UPC-A CodabarEAN-13 UPC-EDelta Code EAN-8Label Code IV Supplement Code for UPC-E, ISBN, EAN-13Modifier Data EditingQualifier Scanner Configuration Manager Everything Else Formula Arrange FormulasIntroduction Programming VIA Scanner InputBeep Quick Setup Bar CodesUPC-E Intercharacter Delay Interblock DelayBeep Tone see page 40 0 None MediumKeyboard Interface 9600 Baud RateParity NoneData Direction for terminal wedge see Send to Host SecondEnter TerminatorCode ID Define Code IDDouble Verification Scanning ModeTrigger Label TypePpoo Code 39 see Symbologies GroupCheck Digit Not Calculate Interleaved 2 of 5 ITF seeCode 32 Italian Pharmacy see Standard 2 China Postal Code Toshiba CodeTelepen UCC/EAN 128 seeDefine Minimum and Maximum Length Define the EAN 128 Fields SeparatorDefine a Separator for Double Labels MSI / Plessey Code Code 128 seeNo Send Check Digit Double Module Code 93 seeCodabar see Code 11 Special seeNo Send Label Code IV and V seeExit EAN-8 EAN-13 seeDelta Distance Code see Supplement Code seeOff / On Qualifiers Special Characters ModifiersSpecial Characters in this section Code TypeFormula Format TCP/IP Function Codes for PC Characters in parentheses represent Extended Code Ascii Chart= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Generic Scanner Troubleshooting Tips TroubleshootingProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char