Unitech MS860 manual Buzzer

Page 8

INTRODUCTION

Buzzer

The MS860 provides audible feedback while it is in operation. These sounds indicate the operating status of the scanner.

One High Tone Beep

The scanner will beep once after successfully reading a bar code.

One High-Low-High Beep

After scanning a ‘begin configuration’ bar code (“Enter Group 5”, for instance), the scanner LED will flash green while the scanner simulta- neously gives one high-low-high tone beep. Upon exiting configuration mode by scanning an “Exit” bar code, the scanner will give one high tone beep, and the scanner LED will stop flashing.

Continuous High-Low Beeps

If scans are attempted out of range, communication will be broken. The scanner LED will remain red and you will hear a continuous high- low beep from the scanner when you scan bar codes.

If the Access Point is powered off, this means the communication between the scanner and the Access Point is lost. You will also hear a continuous high-low beep from the scanner when you scan bar codes.

MS860 WiFi Manual

6

Image 8

Contents MS860 WiFi Bar Code Scanner Table of Contents Introduction IntroductionQuick Start Important Notes Importantscanner Ndotesaccessories Scanner Parts Scanner LEDBuzzer Cradle Parts Cradle LEDsHow to determine if the scanner needs recharging Charging the ScannerNetwork Settings Modifying the WiFi settings Glossary IP AddressWEP Network Settings Using SCM for Scanner Network SettingNetwork Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Beeps and Delays Interblock DelayIntercharacter Delay Keyboard WedgeFunction Code Caps-LockLanguage Use Numeric KeypadBaud Rate ParityData Bit HandshakingRS232 BCC CharacterTime Out Data DirectionScanner Port TerminatorUse Code ID Double VerificationSettings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Scanning Mode Label TypeAim Function for Long Range Engine Aiming Time for Long Range EnginePreamble PostambleBar Code Symbologies CodeInterleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code Codabar UPC-AUPC-E EAN-13EAN-8 Delta CodeSupplement Code for UPC-E, ISBN, EAN-13 Label Code IVModifier Data EditingQualifier Scanner Configuration Manager Arrange Formulas Everything Else FormulaProgramming VIA Scanner Input IntroductionQuick Setup Bar Codes BeepUPC-E Interblock Delay Intercharacter DelayBeep Tone see page 40 0 None MediumKeyboard Interface Baud Rate 9600Parity NoneSecond Data Direction for terminal wedge see Send to HostTerminator EnterCode ID Define Code IDScanning Mode Double VerificationTrigger Label TypePpoo Symbologies Group Code 39 seeCheck Digit Not Calculate Interleaved 2 of 5 ITF seeStandard 2 China Postal Code Toshiba Code Code 32 Italian Pharmacy seeTelepen UCC/EAN 128 seeDefine Minimum and Maximum Length Define the EAN 128 Fields SeparatorDefine a Separator for Double Labels Code 128 see MSI / Plessey CodeNo Send Check Digit Double Module Code 93 seeCode 11 Special see Codabar seeNo Send Label Code IV and V seeExit EAN-13 see EAN-8Delta Distance Code see Supplement Code seeOff / On Qualifiers Modifiers Special CharactersSpecial Characters in this section Code TypeFormula Format TCP/IP Function Codes for PC Ascii Chart Characters in parentheses represent Extended Code= %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Troubleshooting Generic Scanner Troubleshooting TipsProblems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char