Panasonic AW-PH360N manual $ Setting the cable compensation circuit of video signals

Page 12

Installation (The installation work must be performed by your dealer without fail.)

$ Setting the cable compensation circuit of video signals

(COMP switch of the COMP printed circuit board is set to “OFF” in the default setting.)

1When using the AW-RP501 controller or the AW-HB505 multiport hub (for transmissions using composite signals)

When this controller (or multiport hub) has been connected to the pan/tilt head, it is permissible for the connecting cables to be up to 1640 ft. (500 m) long when a 10BASE-T straight cable (UTP category 5) and coaxial cable (BELDEN 8281) are used. However, when the cable length exceeds 984 ft. (300 m), follow the steps below to set the cable compensation circuit to “1”. (Default setting: OFF)

1.Remove the four screws on the base connector rear panel, and pull out the panel toward you.

2.Set the COMP switch on the COMP printed circuit board at the back of the panel to “1”.

3.Return the panel to its original position and secure it in place using the four screws.

2When using the AW-RP605A controller

When this controller has been connected to the pan/tilt head, it is permissible for the connecting cables to be up to 3333 ft. (1000 m) long when a 10BASE-T straight cable (UTP category 5) and coaxial cable (BELDEN 8281) are used. However, when the cable length exceeds 1640 ft. (500 m), follow the steps below to set the cable compensation circuit to “2”. (Default setting: OFF)

1.Remove the four screws of the base connector rear panel, and pull out the panel toward you.

2.Set the COMP switch on the COMP printed circuit board at the back of the panel to “2”.

3.Return the panel to its original position and secure it in place using the four screws.

3When using the AW-RP400 controller

When this controller has been connected to the pan/tilt head, it is permissible for the connecting cables to be up to 1640 ft. (500 m) long when a 10BASE-T straight cable (UTP category 5) and coaxial cable (BELDEN 8281) are used.

Since the AW-RC400 cable compensation unit is capable of providing cable compensation for distances up to 1640 ft. (500 m), there is no need to change the setting established for the pan/tilt head’s cable compensation circuit.

4When using a personal computer as the controller (for transmissions using component signals) and the configuration described in 1

A separate cable compensation unit is required if the cables used to connect the pan/tilt head and controller are to be run over a long distance.

<Note>

OBefore setting the switches, make absolutely sure that the power of the AC adapter which is to be connected to the pan/tilt head is set to OFF.

- 12 -

Image 12
Contents AW-PH360N Indicates safety information FCC Note Contents AccessoriesIntroduction Installation precautions Precautions for use Parts and their functions Tilting arm Suspended installation Stand-alone installation $ Assembling the pan/tilt headOAttaching the tilting arm For suspended installation For stand-alone installationFor a soft landing For a precise landing$ Transmission signal selection setting OAnalog/IEEE1394 card settings Oweb card settingsOsdi settings Connector printed circuit board$ Setting the cable compensation circuit of video signals When using the AW-RP605A controllerWhen using the AW-RP400 controller $ Installing the pan/tilt head Suspended installation $ Mounting the cameraMounting example when the camera side is heavy Mounting example when the lens side is heavyOAttaching the chain With the AW-E350/AW-E650With the AW-E655/AW-E750/AW-E860 OAdjusting slack in the chain OMounting a cameraWith the AW-E350/AW-E650 With the AW-E655/AW-E750/AW-E860 Connections Monitor Connections Compensation unit $ Connecting the connector panel RS-232C control Zoom lens RS-232C cable AW-CA28T9$ Head connector panel As viewed from cable endConnector Pb OUT connector $ Connecting the AC adapter for use with the pan/tilt head DC 12V in terminal board$ Connection examples 10BASE-TAW-PS300A AC adapter AW-PS300A Equivalent to UTP Category 5 straight Cable, max ft 10 m Equivalent to Belden AW-RP605A Coaxial cable Camera cable supplied Panel is used to control the camera Coaxial cable Belden 8281, max ft m Color monitor AW-RC400 Connections Personal computer Belden 8281, max AW-CA50F29 AW-CA50E29 Limiters $ Setting/releasing the limiters OFor the controller AW-RP301/AW-RP305/AW-RP501/AW-RP505OFor the controller AW-RP605A OFor the controller AW-RP400 Replacement of consumable parts $ Replacing the battery$ Replacing the motor $ Replacing the gearSpecifications $ Functions/performance Page Page Panasonic Broadcast & Television Systems Company