Panasonic WJ-MP204C manual Alarm mode setup, Alarm Data, Alarm CAM no PRE 1CH 2CH 3CH 4CH

8Alarm mode setup

1.Move the cursor to ALARM MODE to select ON or OFF with the [–] or [+] button, then press SET. The default setting is ON.

ON : Opens a submenu shown below.

OFF: Alarm mode is disabled.

The ALARM MODE sub menu appears.

ALARM MODE
MONITOR SPOT
	ON
ALARM DISPLAY
	ON
SITE ALARM
	ON
TERM.ALARM
	ON
ALARM OUTPUT
	10S
ALARM DATA
	1S

1-1. Move the cursor to MONITOR SPOT to select ON or OFF with the [–] or [+] button, then press SET. The default setting is ON .

This setting specifies whether to change the monitor image when an alarm operates.

ON : Image display on the monitor changes to that of the alarm activated channel.

OFF: Image display will not change even when an alarm operates.

The MONITOR SPOT sub menu appears.

	MONITOR SPOT
ALARM	CAM NO.		PRE
1
		1CH		-
2
		2CH		-
3
		3CH		-
4
		4CH		-

1-2. In this setup, the relation is established between four alarm channels and four camera channels, along with the preset positions to which the camera moves when the alarm operates.

1-2-1. Move the cursor to a channel of CAM. NO with the [D] or [C] button.

1-2-2. Select a CAM. NO with the [–] or [+] button, then press the [C]. The cursor moves to PRE. The default setting is that the same numbers are assigned to both alarm channel and camera chan- nel.

1CH: Camera input 1 will be displayed when the respective alarm operates.

2CH: Camera input 2 will be displayed.

3CH: Camera input 3 will be displayed.

4CH: Camera input 4 will be displayed.

1-2-3. Select a PRE (preset position number) with the [–] or [+] button, then press the [C].

1-2-4. Repeat above steps for other alarm channels.

1-2-5. Press the ESC to return to the ALARM MODE menu.

2.Move the cursor to ALARM DISPLAY. Select ON or OFF with the [–] or [+] button. The default setting is ON. Alarm display “ALARM ***” on the monitor is enabled or disabled while an alarm is in operation. “***” is the alarm channel number.

ON: Enabled.

OFF: Disabled.

3.Move the cursor to SITE ALARM. Select ON or OFF with the [–] or [+] button. The default setting is ON.

A site alarm (motion detection) generated by a camera is accepted or ignored.

ON: Enabled.

OFF: Disabled.

4.Move the cursor to TERM. ALARM (terminal alarm). Select ON or OFF with the [–] or [+] button. The default setting is ON.

An alarm input to the rear terminal is accepted or ignored.

ON: Enabled.

OFF: Disabled.

5.Move the cursor to ALARM OUTPUT. Select an output duration with the [–] or [+] button. The default setting is 10S (seconds).

The output status is supplied to the terminals on the rear. The output is reset along with the activated alarm according to this setup.

EXT: The output is reset when a reset input is supplied to the rear panel or the alarm reset button is pressed on the front panel.

1S-5MIN:The output is reset when the preset duration elapses.

OFF: No output.

6.Move the cursor to ALARM DATA. Select an output time with the [–] or [+] button. The default setting is 1S (sec- ond).

The unit notifies the connected System Controller (must be set to Unit #1) of the alarm activation once every period preset by this setup.

OFF: No notification.

0S: Notification is made immediately.

1S: Notification is made once every 1 second.

5S: Notification is made once every 5 second.

7.Press the ESC to go back to the SYSTEM menu.

22