Avery ALS 230 manual Inserting label material, Left hand version

Page 26

Operators Manual

ALS 230

4.2 Inserting label material

Attention:

Before threading the new material, the waste paper should be removed.

CAUTION! - Isertion/exchange of material should be carried out only by especially instructed personal.

Threading of the label material is shown down below on the threading diagrams for the right-hand and the left-hand version.

left hand version

right hand version

 

 

 

 

 

 

Figure 7 Threading diagram

yHang document material in reel holder in a way to ensure unwinding that label in the printer section is on the top. Put outer guide disk onto mandrel. The two guide plates keep the label roll reliably in position on the unwind mandrel.

yGuide material around the dancer arm.

yLabels behind the dispensing edge should be removed. The material brush has to be positioned in a way, that the material is kept tight. From time to time, it is recommended to reverse the mounting of the brush while you are loading a new label roll.

yAdjust the pressure roller before the rewind, so that it is right in the middle of the material. Close the pressure roll and turn the roll 2 or 3 times, so that the material is threaded. Check that the material is guided straight.

yCheck correct position of the label sensor.

Release 11/05

Page 24

Operation

Image 26
Contents Page Page ALS Menu structure Errors and warnings Manufacturer Important NotesOverview CopyrightSafety General Safety NotesOperator’s duty of care Concrete security regulations and symbols used Security measures during maintenance and repairs Security measures during normal operationObserve environmental regulations Work on the electrical equipmentWork on pneumatic equipment Page Description MechanicsDispensing mechanics Operator panel Operator panelALS Plug board ElectronicALS Preparing the machine InstallationGeneral setting Unpacking of the unitDefine label data Prepare dispensingInsert material Capacitive label sensor Setting Lpit manuallyManual adjustment of the Cont parameter Label guide Capacitive sensorFixed dispensing speed Adjust dispense functionStop position Product data bank Automatic dispensing speed ApsfLabel position on the product Safety recommendation OperationInserting label material Left hand version3Initialise new label material Dispenser Menu selection Function Display message Mains switch4Control of dispense unit Missing label function and web breaksMaterial initialisation Init Dispenser active onDispenser stopped OFF Label positionPOSStop position Stod Label positionBlow on time Blow Start delaySTADDispense speed Velo Product menu PD0nMaintenance Standard menu Configuration menuMenu structure Extended standard menuApplicator ConfigurationStandard menu  Direct Extended menuDisplay Function Values Standard menuInitialisation Init Labelling time Blow Start delay StadLabel position POS Dispensing speed VeloExtended standard menu Display Function Data valueSensor status Sens Label pitch LpitLabel contrast Product length Prdl Slew speed Slew Electronic gear ratio adjustment EgraEgra value check Stst Dwell time APT1Time constant compensation APT4 Restart delay APT3Blow on time APT2 Save parameter in data bank Save End of air stream signal AstpPrinter dwell time PDT Load data bank LoadProduct menu Release 11/05 Menu structure Calling the configuration menu ConfigurationPossible adjustments Possible testsHandling the menu Display Function of the parameter Possible data entryMenu functions Automatic product speed followerAPSF Type of applicator ApplAdditional functions in the standard menu Input and sensor check ICHOutput check OCH Parity bit Pari Adjustment resettingFACTInterface baud rate Baud Number of stop bits SbitDistance sensor to dispensing edge Dist Number of data bits DbitRecycle simulates max labels/min Recy Label counter LabcRelease 11/05 Configuration Serial interface Data of the serial interfaceExample Interface commandsCommand Description Range Ledg Bit definition in warning flag Bit definition in error flagError number Error message in display Error description Message in displayConnections and signals Output signalsSignals for direct dispense Applicator modesControl signals for the ASA applicator Timing ASA applicatorSignals for the EP applicator APT2Applicator connector Applicator connectorInput signals Connecting NPN left or PNP right inputsExample for connecting an NPN sensor Datalogic Product sensorOD Control sensor NPN connection of optional ODC sensorApsf sensor Connection of a NPN type Apsf sensorControl signals Optional connector for process controInternal I/O connector EMI RuleElectronic diagrams Wiring diagramLayout dispenser electronic board Jumper position has to be 800 steps Page STO! Power-fail message Errors and warningsDispenser error messages Message Meaning How to solveInto Dispenser warnings EepromALS Description Details Technical SpecificationTechnical Information Application specification APSF- Sensor Specification Optional functionPerformance Labels per minute in relation to different label pitches375 125 875 625 ALS Page Adjustment Function Factory ApplicationFunction Factory PD01 PD02 PD03 PD04 Function PD05 PD06 PD07 PD08 PD09Index Siehe Machine type