Panamax MB1000 manual Communications Protocol, Controller Commands, ALL on, All Off

Page 10

RS-232 Communications Protocol & Command Set

Communications Protocol

Connector Pin-out:

Pin 2, Transmit. The MB1000 transmits data on this pin. Pin 3, Receive. The MB1000 receives data on this pin. Pin 5, SG (signal ground).

1

RS232 Pin-out

 

1

 

 

6

Pin 2 -Transmit

Pin 2 -Transmit

6

2

2

7

Pin 3 - Receive

Pin 3 - Receive

7

3

3

8

 

 

8

4

 

 

4

9

Pin 5 - Signal Ground

 

9

5

 

5

Baud Rate:

2400bps

Start Bits:

1

Data Bits:

8

Stop Bits:

1

Parity:

None

Flow Control:

None

Controller Commands

Commands and responses are in the form of ASCII character strings terminated with a carriage return <CR> ASCII character 13 (hex).

If the state variable LINEFEED MODE = ON, a linefeed charac- ter (<LF>, 0Ah, 10d) will follow the carriage return.

Incoming messages (to the MB1000) shall be terminated with one of the following characters: NUL (00h, 00d),

carriage return (<CR>, 0Dh, 13d) or line feed (<LF>, 0Ah, 10d).

The following are commands sent by the controlling equipment to the MB1000.

Note: Responses are only transmitted if unsolicited feedback is enabled (!SET_FEEDBACK)

ALL ON

Turns on all outlets. Turn on is immediate with no delay.

Send to UPS:

!ALL_ON<CR>

_____________________________________________

If power is not switched off due to low battery conditions:

Action:

Turn on Outlet Bank 1

Response from UPS:

$BANK 1 = ON<CR>

_____________________________________________

If UPS battery level > Shutoff Threshold

Action:

Turn on Outlet Bank 2

Response from UPS:

$BANK 2 = ON<CR>

_____________________________________________

If UPS battery level < Shutoff Threshold

Action:

Turn off Outlet Bank 2

Response from UPS:

$BANK 2 = OFF<CR>

 

$BATTERY = charge%<CR>

_____________________________________________

Action:

Activate Power Button

Response from UPS:

$BUTTON = ON<CR>

_____________________________________________

The MB1000 shall discard the incoming message under the fol- lowing conditions:

The message overruns the receiver buffer (32 characters).

No terminating character (NUL, <CR>, <LF>) is received within 500ms of receipt of the last character.

ALL OFF

Turns off all outlets.

Send to UPS:

Action:

Response from UPS: Response from UPS: Response from UPS:

Turn off is immediate with no delay.

!ALL_OFF<CR>

All outlets will turn off

$BANK 1 = OFF<CR> $BANK 2 = OFF<CR> $BUTTON = OFF<CR>

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Features MB1000 InstructionsTable of Contents Before You Begin Unpacking Inspect the UPS upon receiptImportant Safety Instructions Battery replacement recommended every two yearsInput Installing Your UPSAC Power UPS OutputPower Switch Basic Operation Front Panel DescriptionOperating Modes Setup Mode Flowchart Advanced Operation RS-232 Control with Open Protocol RS-232 Communications Protocol & Command SetTo program IR output RS-232 serial interface can be used in the following waysALL on Controller CommandsCommunications Protocol ALL OFFSET Buzzer Mode Switch Outlet BankSET Bank 2 Threshold SET Linefeed Mode SET AVR ModeSET Feedback Mode SET Display Sleep ModeQueries Identify Reset Factory SettingsPower Status Outlet StatusPower Button Status Change Condition Response Battery Level StatusList Configuration Power Fault Status Change Condition ResponseLimited Product Warranty FCC Notice and WarrantiesCaractéristiques Avant de commencer Table des matièresUn câble USB Ne tentez pas le remplacement de la batterie Les dispositifs fournis par PF Power ne sont pas destinésPour votre sécurité Alimentation c. a Installation de votre onduleurAlimentation Sortie onduleurManœuvres de base Description DU Panneau Frontal InterrupteurModes de fonctionnement IR1 Test IR1 Program IR1 Sample Fail Manœuvres complexes Pour programmer les émissions infrarouges Protocole de communication et jeu de commandes RS-232Contrôle RS-232 avec protocole libre Activation Générale Commandes de contrôleProtocole de communication Désactivation GénéraleConfigurer LE Mode DE Signal D’ALARME Configurer LE Seuil Plancher DU BlocBasculer UN Bloc DE Prises Configurer LE Mode Saut DE Ligne Configurer LE Mode DE Régulation Automatique DE LA TensionConfigurer LE Mode DE Réponse Configurer LA LuminositéÉtat DU Courant Requêtes IdentificationÉtat DES Prises TensionsChangement D’ÉTAT DE L’INTERRUPTEUR Condition Réponse Liste DES ConfigurationsCharge DE LA Batterie Changement D’ÉTAT DU Courant Condition RéponseAvis FCC et garanties AvertissementMB1000 Instrucciones CaracterísticasPágs , 9, 10, 11 Tabla de contenidoCable USB Instrucciones de seguridad importantes ¡IMPORTANTECorriente alterna Instalación del suministro de energía ininterrumpible UPSEntrada Salida de UPSOperación básica Descripción DEL Panel Frontal Infrarroja IRModos de operación IR1 Test IR1 Program IR1 Sample Fail Operación avanzada Protocolo de comunicaciones RS-232 y conjunto de comandos Para programar la salida IREncender Todo Protocolo de comunicacionesComandos del controlador Apagar TodoConfigurar Modo DE Zumbador Configurar Umbral DE RegletaConmutar Regleta Configurar Modo DE Salto DE Línea Configurar Modo AVRConfigurar Modo DE Realimentación Configurar Brillo DEL MedidorEstado DE Alimentación Consultas IdentificaciónEstado DE Regletas VoltajeCambio DE Estado DE Regleta Listar ConfiguraciónEstado DE Nivel DE Batería Condition ResponseNotificación de la FCC Notificación de la FCC y garantíasGarantía de dos años de la batería

MB1000 specifications

The Panamax MB1000 is a prominent addition to the maritime industry, recognized for its advanced features and capabilities that cater specifically to the transportation and cargo handling sectors. Designed with a focus on efficiency and performance, this vessel has become a preferred choice among shipping companies looking to optimize their operations.

One of the main characteristics of the MB1000 is its impressive cargo capacity. With a deadweight tonnage exceeding 60,000 tons, the vessel is engineered to carry a significant amount of cargo, making it an ideal solution for bulk carriers. This capacity is coupled with a well-designed hull that ensures stability and speed, allowing for quick turnarounds and efficient voyages.

The MB1000 is equipped with state-of-the-art propulsion technology. It features a powerful diesel engine that delivers high output while maintaining fuel efficiency. The combination of low fuel consumption and reduced emissions aligns with global environmental standards, making the MB1000 a more eco-friendly choice in the industry.

In terms of navigation and safety, the vessel is outfitted with advanced electronic systems. The integrated bridge system includes radar, GPS, and autopilot functions that enhance situational awareness for the crew, ensuring safer and more precise navigation across various maritime conditions. Furthermore, the vessel adheres to the latest safety regulations, equipped with life-saving equipment and fire-fighting systems to ensure the utmost safety for the crew and cargo.

The design of the MB1000 also emphasizes crew comfort and operational efficiency. The ship features spacious accommodations, including well-appointed cabins and common areas designed to provide a restful environment during long voyages. The operational areas are meticulously arranged to facilitate smooth workflows for the crew, improving overall productivity.

Additionally, the Panamax MB1000 is built for adaptability, enabling shipping companies to adjust the interior layouts and equipment based on specific cargo requirements. This flexibility, combined with cutting-edge engineering and innovative technologies, solidifies the MB1000’s reputation as a modern workhorse in the maritime sector.

Overall, the Panamax MB1000 stands out as a sophisticated vessel that encapsulates the evolution of maritime technology, combining performance, safety, and environmental consciousness, making it a valuable asset for any shipping fleet.
Top Page Image Contents