B&K 1788, 1786B Initiating the Output stateINIT OUT, Initiating the Output Voltage Init Volt

Page 17

Step2. Select >MAX VOLT by using? and ? key.

Step3. Press Enter key.

Step4. Change the voltage value by using numeric keys 0 to 9 or ? and ? key. Step5. Press Enter key.

Note: After you setting the maximum voltage value, the output voltage setup should be in the range from 0 volt to maximum voltage. The default maximum voltage is the full voltage range of its model.

nInitiating the Output state(>INIT OUT)

This instruction can initiate the output state when the power supply is powered on. If you select ON, the power supply will initiate the output to OFF state when the power supply is powered on. If you select OFF, the output will remain the same state as last time you turned off the power supply

Note: Default selection is ON and the output state is always OFF state.

nInitiating the Output Voltage (>INIT VOLT)

This instruction can set the initial output voltage. If you select ON, the power supply will initiate the output voltage to 0Volt when the power supply is powered on. If you select OFF, the output voltage

will remain as the same volts as the last time you turned off the power supply

Note: Default setting is ON and the output voltage is 0 volt.

nSetting the Key Sound(>KEY SOUND)

This instruction can switch on/off the buzzing sound when you press any key, If you select ON, the buzzer will sound when any key was pressed. If you select OFF, the buzzer will not sound when the keys were pressed.

Note: Default setting is ON; the buzzer will sound when you press any key.

nSetting the Baud Rate(>BAUDRATE)

This instruction can change the communication baud rate for the power supply, the baud rate range is 4800, 9600, 19200 or 38400? Before the communication, you must make sure that there is same baud rate between the power supply and the computer.

Note: Default baud rate is 4800.

17

Image 17

Contents Page Content Quick Reference About your safetyGeneral information Protection from electric shockCertification Certification and WarrantyIntroduction Front Panel at a Glance Display annunciators Function keys descriptionMenu description Cal Rear Panel at a GlanceQuick Start Connect the power cord and turn on the power supplyPreliminary Checkout Check the list of supplied itemsCurrent Output Checkout Output CheckoutVoltage Output Checkout To Adjust the Carrying Handle If the Power Supply Does Not Turn OnVerify that there is AC power to the power supply Verify the power-line voltage settingBench-top viewing positions Carrying position To Rack Mount the InstrumentSpecifications SpecificationsMaximum input power Supplemental CharacteristicsEnvironmental Conditions Unit mmConstant Voltage Operation Front-panel OperationFront-panel Operation Overview Saving and Recalling Operation Constant Current OperationMenu Operation Set Maximum voltageMAX VoltSetting the Baud RateBAUDRATE Setting the Key SoundKEY SoundInitiating the Output stateINIT OUT Initiating the Output Voltage Init VoltSetting password for function keysKEY Lock Setting Address AddressIT-E131 Communication cable Remote Operation ModeCommunication setting Frame format Setting the remote control mode 20HCommunication protocol DescriptionSetting the output voltage 23H Setting the output state ON/OFF 21HSetting the maximum output voltage 22H Setting the communication address 25H Setting the output current 24HReading the calibration state 28H Entering the calibration mode 27HCalibrate the current value 2BH Calibrating the voltage value 29HReading calibration information 2FH Setting calibration information 2EHSave the calibration data to Eeprom 2DH Return information of command operation in power supply 12H Restore the factory default calibration data 32HEnable the local key 37H Calibration Voltage calibration ConfigurationCurrent calibration Finish calibratingPV1785B1788 Software Reset to the default calibration settingsInstallation Functions of PV1785B1788 Status bar 1Configure the systemQuickly setting Setting Voltage and current4. GO/NG Test Function Program settingSave and Open Present Voltage/Current ChartChart Description Page Limited One-Year Warranty Service Information USA