Epson M147C, M147B manual Safety Precautions

Page 4

English

Safety Precautions

This section presents important information intended to ensure safe and effective use of this product. Please read this section carefully and store it in an accessible location.

WARNING:

Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire. Immediately unplug the equipment and contact your dealer or a SEIKO EPSON service center for advice.

Never attempt to repair this product yourself. Improper repair work can be dangerous.

Never disassemble or modify this product. Tampering with this product may result in injury or fire.

Be sure to use the specified power source. Connection to an improper power source may cause fire.

Do not allow foreign matter to fall into the equipment. Penetration by foreign objects may lead to fire.

If water or other liquid spills into this equipment, unplug the power cord immediately, and then contact your dealer or a SEIKO EPSON service center for advice. Continued usage may lead to fire.

CAUTION:

Do not connect cables in ways other than those mentioned in this manual. Different connections may cause equipment damage and burning.

Be sure to set this equipment on a firm, stable, horizontal surface. Product may break or cause injury if it falls.

Do not use in locations subject to high humidity or dust levels. Excessive humidity and dust may cause equipment damage or fire.

Do not place heavy objects on top of this product. Never stand or lean on this product. Equipment may fall or collapse, causing breakage and possible injury.

To ensure safety, unplug this product before leaving it unused for an extended period.

Do not touch the thermal head or paper feed motor. Wait for the head and the motor to be cool. The head and the motor can be very hot after printing for a long time. Touching them may cause burns.

2TM-H6000II User’s Manual

Image 4
Contents TM-H6000II Serial EMC and Safety Standards Applied FCC Compliance Statement For American UsersCE Marking TM-H6000II User’s ManualSafety Precautions Connectors LabelsInstalling the Paper Roll Installing the Ribbon Inserting Slip Paper Troubleshooting Error light on or blinkingMicr and Endorsement Printing Factory installed options Cleaning the Print HeadReading Micr Characters On Personal Checks Cleaning the Micr Mechanism Be sure not to use an adhesive cleaning sheetEndorsement Printing Do not open the unit during printing TM-H6000II Specifications TM-H6000II User’s Manual Deutsch Geltende EMC- und Sicherheitsnormen SicherheitsvorkehrungenWarnung CE-PlaketteVorsicht Etiketten Einlegen der PapierrolleAnschlüsse Einlegen des Farbbandes Einlegen von PapierblätternFehlerbehebung Reinigung des DruckkopfesMICR- und Indossierdruck werksseitig installierte Optionen Lesen von MICR-Zeichen auf SchecksReinigen des MICR-Mechanismus Kein Reinigungsblatt mit haftender Oberfläche verwendenHinweise zur Verwendung des MICR-Lesers IndossierdruckDie Einheit nicht während des druckens öffnen Technische Daten des TM-H6000II Nederlands Elektromagnetische compatibiliteit en veiligheidsnormen VeiligheidsmaatregelenWaarschuwing CE-keurmerkLET OP Installeren van de papierrol Installeren van het lint Inbrengen van het bonpapierProbleemoplossing Reinigen van de printkopReinigen van het MICR-mechaniek Lezen van MICR-tekens op persoonlijke chequesGeen zelfklevende reinigingsvellen gebruiken Zet de stroom uit voordat u een lintcassette installeert EndosserenOpmerkingen bij gebruik van de MICR-lezer De unit niet openen tijdens het afdrukkenSpecificaties voor de TM-H6000II Français Normes EMC et de sécurité Consignes de sécuritéMise EN Garde Label CEÉtiquettes Installation de la bobine papier ConnecteursInstallation du ruban Introduction d’un feuilletDépannage Nettoyage de la tête d’impressionNettoyage du lecteur de caractères magnétiques Lecture des caractères magnétiques des chèques personnels’emploi de feuillets de nettoyage adhésifs est à bannir Remarques sur l’emploi du lecteur de caractères magnétiques Impression d’endosNe pas ouvrir l’unité pendant l’impression Fiche technique des modèles TM-H6000II Português EMC e padrões de segurança aplicados Precauções de segurançaAdvertência Marca CECuidado Etiquetas Instalação do papel em roloConectores Resolução de problemas Instalação da fitaIntrodução do papel tipo recibo Limpeza da cabeça de impressãoLimpeza do mecanismo Micr Leitura de caracteres Micr em cheques pessoaisAssegure-se de não usar uma folha de limpeza adesiva Notas sobre o uso da leitora Micr Impressão de endossoNão abra a unidade durante a impressão Especificações da TM-H6000II Español Normas de ECM y de seguridad aplicadas Precauciones de seguridadAdvertencia Marcas de CEPrecaución Instalación del rollo de papel NotaResolución de problemas Instalación de la cintaInserción de papel para boletas Limpieza de la cabeza de impresiónLimpieza del mecanismo Micr Lectura de caracteres Micr en los cheques personalesTenga cuidado de no utilizar una hoja de limpieza adhesiva Notas acerca del uso del lector Micr Impresión de endososNo abra la unidad mientras ésta esté imprimiendo Especificaciones de la impresora TM-H6000II TM-H6000IIP Standard EMC e di sicurezza applicati in questo prodotto Precauzioni di sicurezzaAvvertenza Contrassegno CEAttenzione Etichette Installazione del rotolo della cartaConnettori Installazione del nastro Risoluzione di problemiInserimento di un foglio di carta mobile Pulizia della testina di stampaPulizia del meccanismo Micr Lettura di caratteri Micr sugli assegni bancariNon usare un foglio detergente adesivo Stampa del timbro bancario Non aprire l’unità durante la stampaSpecifiche TM-H6000II Page 2000.12