Toshiba IPE002Z instruction manual Introduction, Handling in general, Network control

Page 2

E6581741

Introduction

Thank you for purchasing the “EtherNet/IP™ - Modbus® TCP option (IPE002Z)” for TOSVERT VF-MB1/S15 inverter. Before using EtherNet/IP™ - Modbus® TCP module, carefully read this function manual in order to completely and correctly utilize its excellent performance.

This option needs the option adaptor to connect VF-S15 which type form is SBP009Z. Please match here and buy it when SBP009Z is not at hand yet.

After reading this function manual, please keep it handy for future reference.

For details of its general handling, see an instruction manual attached with the option unit.

-TOSVERT VF-MB1 Instruction Manual ························································· E6581697

-TOSVERT VF-S15 Instruction Manual ·························································· E6581611

-TOSVERT VF-MB1/S15 communication option Precautions Manual··········· E6581739

-TOSVERT VF-MB1 Communication Function Instruction Manual················ E6581726

-TOSVERT VF-S15 Communication Function Instruction Manual················· E6581913

EtherNet/IP™ is a trademark of ControlNet International, Ltd.

Modbus® TCP is a registered trademark of AEG Schneider Automation International S.A.S.

Handling in general

 

 

 

Warning

 

 

 

Do not connect or disconnect a network cable while the Inverter power is on.

 

Prohibited

It may lead to electric shocks or fire.

 

 

 

 

 

See the instruction manual attached with the option unit for cautions the handling.

 

Mandatory

Otherwise, it may lead to electric shocks, fire, injuries or damage to product.

 

 

 

 

Network control

 

 

 

 

 

 

 

Warning

 

 

 

Do not send the value out of the valid range to objects and attributes.

 

Prohibited

Otherwise, the motor may suddenly start/stop and that may result in injuries.

 

 

 

 

 

Use an additional safety device with your system to prevent a serious accident due to the

 

Mandatory

network malfunctions. Usage without an additional safety device may cause an accident.

 

 

Caution

Mandatory

Set up “Communication error trip function (see below)” to stop the Inverter when the option unit is deactivated by an unusual event such as tripping, an operating error, power outage, failure, etc.

-Network Time-Out, Inverter operation at disconnection, Preset speed operation selection

(Refer to "3.2.3 Network error detection (c100 - c103, c523)" for details)

Deactivated the option module may cause an accident, if the “Communication error trip function” is not properly set up.

Make sure that the operation signals are STOP before resetting Inverter’s fault. The motor may suddenly start and that may result in injuries.

Notes on operation

Notes

When the control power is shut off by the instantaneous power failure, communication will be unavailable for a while.

The Life of EEPROM is approximately 100,000 times. Avoid writing a command more than 100,000 times to the same parameter of the Inverter and the option module.

--11--

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Tosvert VF-MB1/S15 Network control IntroductionHandling in general Table of Contents 10.4 10.210.3 12.1Names and functions Connector to the inverter LED indicator SeeOverview OutlineExample of connection to an EtherNet/IP and Modbus TCP RJ45 connector pin layoutEthernet switch Daisy chain topology Star topologyLED indicator Parameters Communication parameters0,0 These fields are effective settings at c504 = 0.0 Display onlyMonitor of the EtherNet error No error/clear error C536 C081 ‘V’ 56H C082 ‘F’ 46H C083 ‘M’ Details of the parameter setting Device name c081-c096Chars No Parameter Character Ex Ascii Ex C084 ‘B’ 42H C085 ‘1’ 31H C086 ‘-‘C504 IP mode Comments Assigning IP addresses c504, c505-c516Network error detection c100 c103, c523 Case of EtherNet/IPTM protocolEtherNet/IP Master VF-MB1/S15Parameter Value Byte ValueBit Function Emergency stop Always enable, E trip Fault resetReset No data is returned from the drive Frequency priority Forced DC Braking Jog run4.3. fa23 Communication command Reserved Electric power quantity4.4. fa07 frequency reference from internal option Specified data outputCompleted, not failure stop Emergency stop No emergency Stop statusStandby Initialization 4.9. fd03 Output current Input terminal function selection 7 f117 FE06Output TB Function select 2A f131 Bit TB Name Function ParameterOutput terminal function selection 1A f130 Output TB Function select F132Supported Objects ObjectsClass Code Object Class Hex Dec Identity Object Class ServiceInstance Services Class AttributesBit Called Definition Attribute 5 State DescriptionsAdapted from document CIP the CIP Networks Library UnsupporteedInstance Attribute Message Router Object0x0E GetAttributeSingle Read one attribute Input Assembly Instance Type Size Assembly ObjectOutput Assembly Instance Type Size See belowInstance 1 Attribute Class ServicesConnection Manager Object Motor Data Object Control Supervisor Object Refer to 4.6.1 Run/Stop Event MatrixE6581741 State of the drive Control Supervisor State Transition DiagramRun/Stop Event Matrix AC/DC Drive Object 0x2A 0x0E GetAttributeSingle0x4000-0x4FFF 0x0000-0x0FFF 0x7000-0x7FFF 0xF000-0xFFFF Range Address accessedParameter Objects 32767Communication No 0003 Instance ID 0x0E GetAttributeSingle 0x10 SetAttributeSingle 0x0001-0xFFFF65535 Read all attributes Read one attribute Port Object 0xF40x01 GetAttributeAll 0x0E GetAttributeSingle TCP/IP interface Object 0xF5 Number of services Optional service listList of optional service codes Bit 5-31 System reserved Only 16 characters in 64 characters can be set in the drive Ethernet link object 0xF6 Bit 7-31 System reserved Shorts Instance 2 Attribute Bit 7-31System reservedInput Instance Configuration of the assembliesOutput Instance Instance name Number Hex SizeInstance 20 CIP basic speed control output Instance 70 CIP basic speed control inputInstance 21 CIP extended speed control output Instance 71 CIP extended speed control inputInstance 100 mapping Byte Bit Instance 100 Native drive outputInstance 150 Native drive input Instance 150 mapping Byte BitExamples of Instance 100/150 ① Stop Byte Hex ④ Preset speed 1 with forward running sr1 Instance Byte Hex⑤ Fault reset Instance Byte Hex ② Forward running 60Hz Instance Byte 15 14 13 12 HexInstance 101 mapping Byte Bit Instance 101 Native drive outputInstance 151 Native drive input Instance 151 mapping Byte BitOutput Instance 0x0268 Input Instance F268 is 60.0Hz 0x1770 Examples of Instance 101/151Output Instance 0x0003 Input Instance Cmod is 0x0000 Instance 102 mapping Bit Byte Instance 102 Native drive outputInstance 152 Native drive input Instance 152 mapping Bit ByteInstance 105 mapping Bit Byte Instance 105 Toshiba specific outputInstance 155 Toshiba specific input Examples of Instance 105/155 Output Instance 0x0000 0x0003 Input Instance Cmod isCreate a new project About EDS fileIntegration in RSLogix Add a EtherNet/IP scanner to the I/O configuration E6581741 Configure the VF-MB1/S15 EtherNet/IP module E6581741 Download the program to the PLC Select the Download Once again, select the Download Edit the I/O scan data E6581741 E6581741 Drive Modbus servers Modbus TCP serverModbus TCP frames List of Modbus functions supportedIllegal Function Illegal Data Address Illegal Data Value 0x03 Read Holding Registers functionFunction Code = 83h Exception Code = Function Code = 86h Exception Code = 0x06 Write Single Register functionByte Meaning 0x10 Write Multiple Registers function Function Code = 97h Exception Code = 0x17 Read/Write Multiple Registers functionFunction Code = 17h 0x2B Read Device identification function Function Code = ABh Exception Code = Obj Length 18-24 Value IPE002ZObj Length 27-30 Value 0106 Exception response format Parameter data Periodic variables IO Scanning servicePresentation Example of the setup with PL7 Defining the hardware configurationBootp configuration Configuring Modbus messaging ModeConfiguring periodic variables PLCCommand & Setpoint selection Local/Remote Operation panel FmodWiring EtherNet/IP-Modbus TCPUnusual diagnosis Option errorDisconnection error of network cable Access to the webserver WebServerWeb pages structure Drive monitor Main menu Monitoring State of the drive can be confirmed on thisDrive parameters Main menu Monitoring Input the write value to popup window Network parameters Main menu Network Setup Modbus scanner Main menu Network SetupEthIP scanner Main menu Network Setup Administration Main menu Network Setup TCP/IP statistics Main menu Diagnostics You can check TCP/IP status on this 88E
Top Page Image Contents