Toshiba IPE002Z instruction manual Input terminal function selection 7 f117, FE06

Page 21

E6581741

3.2.4.13. fc91 (Alarm code)

bit

Function

0

1

Remarks

(Code displayed on

the panel)

	0	Over-current alarm	Normal	Alarming	c flicking
	1	Inverter over load alarm	Normal	Alarming	l flicking
	2	Motor over load alarm	Normal	Alarming	l flicking
	3	Over heat alarm	Normal	Alarming	h flicking
	4	Over voltage alarm	Normal	Alarming	p flicking
	5	Main circuit undervoltage alarm	Normal	Alarming	-
	6	main device overheat alarm	Normal	Alarming	l flicking
	7	Under current alarm	Normal	Alarming	-
	8	Over-torque alarm	Normal	Alarming	-
	9	Braking resistor overload alarm	Normal	Alarming	-
	10	Cumulative operation hours alarm	Normal	Alarming	-
	11	Option communication alarm	Normal	Alarming	-
	12	Serial communication alarm	Normal	Alarming	-
	13	MOFFMS (MSrelay off or MOFF)	Normal	Alarming	-
	14	Stop after instantaneous power off	-	Dec., Under	Refer to f302
	14	Stop after instantaneous power off	-	stop	value
				stop	value
	15	Stop after LL continuance time	-	Dec., Under	Refer to f256
	15	Stop after LL continuance time	-	stop	value
				stop	value

3.2.4.14. fd06 (Input TB Status)

bit	TB Name									Function (Parameter)														0			1
0	F				Input terminal function selection 1 (f111)
1	R				Input terminal function selection 2 (f112)
2	RES				Input terminal function selection 3 (f113)
3	S1				Input terminal function selection 4 (f114)																			OFF			ON
4	S2				Input terminal function selection 5 (f115)																			OFF			ON
4	S2				Input terminal function selection 5 (f115)
5	S3				Input terminal function selection 6 (f116)
6	VIB*1				Input terminal function selection 7 (f117)
7	VIA*1				Input terminal function selection 8 (f118)
5 to 15	(Reserved)				-																					Undefined
Note: Don't use the reserved bit for the judgment.
*1: VIA/ VIB are input terminal function when f109 is logic input.
*The input terminal function is selected by each parameter.
Example: Data set for FE06 when the F and RES terminals are ON = 0005H
	BIT15																							BIT0
	FE06:		0			0		0	0	0	0	0	0	0	0		0	0	0	1		0		1
							0				0					0					5

- 20 -

Image 21

Contents Tosvert VF-MB1/S15 Introduction Handling in generalNetwork control Table of Contents 10.3 10.210.4 12.1Overview Connector to the inverter LED indicator SeeNames and functions OutlineEthernet switch RJ45 connector pin layoutExample of connection to an EtherNet/IP and Modbus TCP Daisy chain topology Star topologyLED indicator Communication parameters Parameters0,0 Display only These fields are effective settings at c504 = 0.0Monitor of the EtherNet error No error/clear error C536 Chars No Parameter Character Ex Ascii Ex Details of the parameter setting Device name c081-c096C081 ‘V’ 56H C082 ‘F’ 46H C083 ‘M’ C084 ‘B’ 42H C085 ‘1’ 31H C086 ‘-‘Assigning IP addresses c504, c505-c516 C504 IP mode CommentsCase of EtherNet/IPTM protocol Network error detection c100 c103, c523Parameter Value VF-MB1/S15EtherNet/IP Master Byte ValueReset No data is returned from the drive Frequency priority Emergency stop Always enable, E trip Fault resetBit Function Forced DC Braking Jog runReserved Electric power quantity 4.3. fa23 Communication commandSpecified data output 4.4. fa07 frequency reference from internal optionEmergency stop No emergency Stop status Standby InitializationCompleted, not failure stop 4.9. fd03 Output current FE06 Input terminal function selection 7 f117Output terminal function selection 1A f130 Bit TB Name Function ParameterOutput TB Function select 2A f131 Output TB Function select F132Objects Class Code Object Class Hex DecSupported Objects Instance Services Class ServiceIdentity Object Class AttributesAdapted from document CIP the CIP Networks Library Attribute 5 State DescriptionsBit Called Definition UnsupporteedMessage Router Object 0x0E GetAttributeSingle Read one attributeInstance Attribute Output Assembly Instance Type Size Assembly ObjectInput Assembly Instance Type Size See belowClass Services Connection Manager ObjectInstance 1 Attribute Motor Data Object Refer to 4.6.1 Run/Stop Event Matrix Control Supervisor ObjectE6581741 Control Supervisor State Transition Diagram Run/Stop Event MatrixState of the drive 0x0E GetAttributeSingle AC/DC Drive Object 0x2AParameter Objects Range Address accessed0x4000-0x4FFF 0x0000-0x0FFF 0x7000-0x7FFF 0xF000-0xFFFF 32767Communication No 0003 Instance ID 0x0001-0xFFFF 655350x0E GetAttributeSingle 0x10 SetAttributeSingle Port Object 0xF4 0x01 GetAttributeAll 0x0E GetAttributeSingleRead all attributes Read one attribute Number of services Optional service list List of optional service codesTCP/IP interface Object 0xF5 Bit 5-31 System reserved Only 16 characters in 64 characters can be set in the drive Ethernet link object 0xF6 Bit 7-31 System reserved Shorts Bit 7-31System reserved Instance 2 AttributeOutput Instance Configuration of the assembliesInput Instance Instance name Number Hex SizeInstance 70 CIP basic speed control input Instance 20 CIP basic speed control outputInstance 71 CIP extended speed control input Instance 21 CIP extended speed control outputInstance 150 Native drive input Instance 100 Native drive outputInstance 100 mapping Byte Bit Instance 150 mapping Byte Bit⑤ Fault reset Instance Byte Hex ④ Preset speed 1 with forward running sr1 Instance Byte HexExamples of Instance 100/150 ① Stop Byte Hex ② Forward running 60Hz Instance Byte 15 14 13 12 HexInstance 151 Native drive input Instance 101 Native drive outputInstance 101 mapping Byte Bit Instance 151 mapping Byte BitExamples of Instance 101/151 Output Instance 0x0003 Input Instance Cmod is 0x0000Output Instance 0x0268 Input Instance F268 is 60.0Hz 0x1770 Instance 152 Native drive input Instance 102 Native drive outputInstance 102 mapping Bit Byte Instance 152 mapping Bit ByteInstance 105 Toshiba specific output Instance 155 Toshiba specific inputInstance 105 mapping Bit Byte Output Instance 0x0000 0x0003 Input Instance Cmod is Examples of Instance 105/155About EDS file Integration in RSLogixCreate a new project Add a EtherNet/IP scanner to the I/O configuration E6581741 Configure the VF-MB1/S15 EtherNet/IP module E6581741 Download the program to the PLC Select the Download Once again, select the Download Edit the I/O scan data E6581741 E6581741 Modbus TCP frames Modbus TCP serverDrive Modbus servers List of Modbus functions supported0x03 Read Holding Registers function Function Code = 83h Exception Code =Illegal Function Illegal Data Address Illegal Data Value 0x06 Write Single Register function Byte MeaningFunction Code = 86h Exception Code = 0x10 Write Multiple Registers function 0x17 Read/Write Multiple Registers function Function Code = 17hFunction Code = 97h Exception Code = 0x2B Read Device identification function Obj Length 18-24 Value IPE002Z Obj Length 27-30 Value 0106 Exception response formatFunction Code = ABh Exception Code = Parameter data IO Scanning service PresentationPeriodic variables Defining the hardware configuration Example of the setup with PL7Bootp configuration Mode Configuring Modbus messagingPLC Configuring periodic variablesOperation panel Fmod Command & Setpoint selection Local/RemoteEtherNet/IP-Modbus TCP WiringOption error Disconnection error of network cableUnusual diagnosis WebServer Access to the webserverWeb pages structure State of the drive can be confirmed on this Drive monitor Main menu MonitoringDrive parameters Main menu Monitoring Input the write value to popup window Modbus scanner Main menu Network Setup Network parameters Main menu Network SetupEthIP scanner Main menu Network Setup Administration Main menu Network Setup You can check TCP/IP status on this 88E TCP/IP statistics Main menu Diagnostics