Xilinx UG518 manual Power Management, Fpgaprogb Pushbutton Switch, Onboard Power Supplies

Page 40

Chapter 1: SP601 Evaluation Board

14. FPGA_PROG_B Pushbutton Switch

The SP601 provides one dedicated, active low FPGA_PROG_B pushbutton switch, as shown in Figure 1-28.

VCC2V5

1 R24

4.7K

5%

2 1/16W

		Pushbutton
	FPGA PROG B	1			4
	FPGA PROG B	1	P1	P4	4
		2				3

			P2
			P2

SW3

UG518_28_070809

Figure 1-28:FPGA_PROG_B Pushbutton Switch Topology

Table 1-21:FPGA_PROG_B Pushbutton Switch Connections

FPGA U1 Pin	Schematic Netname	SW3 Pin

V2	FPGA_PROG_B	1

NET "FPGA_PROG_B" LOC = "V2";

Figure 1-29:UCF Location Constraints for BPI Flash Connections

Power Management

AC Adapter and 5V Input Power Jack/Switch

The SP601 is powered from a 5V source that is connected through a 2.1mm x 5.5mm type plug (center positive). SP601 power can be turned on or off through a board mounted slide switch. When the switch is in the on position, a green LED (DS15) is illuminated.

Onboard Power Supplies

The diagram in Figure 1-30shows the power supply architecture and maximum current handling on each supply. The typical operating currents are significantly below the maximum capable. The board is normally shipped with a 15W power supply, which should be sufficient for most applications.

40	www.xilinx.com	SP601 Hardware User Guide
		UG518 (v1.1) August 19, 2009

Image 40

Contents SP601 Hardware User Guide UG518 v1.1 August 19, 2009 optionalSP601 Hardware User Guide Revision History Date Version RevisionSP601 Hardware User Guide Table of Contents UG518 v1.1 August 19 About This Guide Guide ContentsAdditional Resources Conventions Preface About This Guide Online DocumentMeaning or Use Example Overview SP601 Evaluation BoardAdditional Information Features SP601 Evaluation BoardRelated Xilinx Documents Block DiagramRelated Xilinx Documents Feature SP601 FeaturesDetailed Description SP601 Features Cont’d Number Spartan-6 XC6SLX16-2CSG324 FpgaDetailed Description 2I/O Voltage Rail of Fpga BanksMB DDR2 Component Memory 5DDR2 Component Memory Connections Schematic Netname Memory U2Name 3UCF Location Constraints for DDR2 Sdram Address Inputs 4UCF Location Constraints for DDR2 Sdram Data I/O Pins SPI x4 Flash 6J12 SPI Flash Programming HeaderSchematic Netname Pin #Linear Flash BPI 8UCF Location Constraints for BPI Flash ConnectionsFLASHA6 10UCF Location Constraints for BPI Flash Connections 8PHY Configuration Pins Schematic Netname U3 M88E111 Pin10/100/1000 Tri-Speed Ethernet PHY Bit2 Bit1 Bit0Schematic Netname U3 M88E111 SP601 Evaluation Board 9PHY Connections Cont’dUSB-to-UART Bridge CP2103GM ConnectionsIIC Bus 13IIC Bus TopologyClock Generation 14UCF Location Constraints for IIC ConnectionsVita 57.1 FMC-LPC Connector 16UCF Location Constraints for Oscillator Socket Connections13 LPC Pinout 13 LPC Pinout Cont’d 18UCF Location Constraints for Vita 57.1 FMC-LPC Connections Reference Signal Name Color Label Description Status LEDsSuspend Mode I/O Fpga Awake LED and Suspend JumperFpga Init and Done LEDs Controlled LEDReference Signal Name Color Label Fpga Pin User I/OUser DIP switch Reference Signal Name Color Label Fpga Pin DesignatorUser Pushbutton Switches Gpio Male Pin Header 27UCF Location Constraints for User and General-Purpose I/O Power Management Fpgaprogb Pushbutton SwitchAC Adapter and 5V Input Power Jack/Switch Onboard Power SuppliesPower Management 22Estimated Current Draw Rail Estimated Current aConfiguration Options Jtag ConfigurationConfiguration Options 32VITA 57.1 FMC Jtag Bypass JumperSP601 Evaluation Board References Appendix a References Table B-1Default Jumper and Switch Settings Default Jumper and Switch SettingsType/Function Default Appendix B Default Jumper and Switch Settings Table C-1VITA 57.1 FMC LPC Connections Vita 57.1 FMC ConnectionsLPC Pin FMCLA08N SP601 Master UCF Appendix D SP601 Master UCF SP601 Hardware User Guide NET Fpgacmpmosi NET Smaclkn