Adaptec PCI Ethernet and Fast Ethernet Adapters manual

Page 53

Installing Network Drivers

The drivers are now displayed on the list of drivers.

4Click Add to add the drivers.

Note: If you added all four ports for the ANA-6944A/TX, OS/2 automatically loads as many drivers as you need when you reboot.

5Select the appropriate protocols and click Add.

Note: If you need to configure each port with different protocols, pay attention to the order of binding. The first device on your list installs the driver for port 1 (the top connector on the card and the furthest from the PCI bus connector). The second device loads port 2 (next to port 1), and so on.

6Shutdown OS/2 and reboot for your network driver and protocol(s) to take effect.

Installing the Drivers for a Pre-existing OS/2 SMP

Use the following instructions if you already have OS/2 SMP or OS/2 Peer Client installed on your machine. If you are installing OS/2 SMP for the first time, see Installing OS/2 SMP for the First Time on page 4-26.

1On your desktop, double-click the MPTS (Multi-Protocol Transport Services) icon.

2Select Install.

3Select Install Additional Network Drivers, and specify a:\ndis.os2 as the source. Select OK.

4After the OS/2 driver is copied from the diskette, select OK.

5Select Configure.

6Select LAN Adapters and Protocols and then click Configure.

7In the LAPS dialog box, under Network Adapters, highlight the ANA-6944A/TXand click Add. Repeat this three times to add the other three ports as separate devices.

4-25

PCI Ethernet and Fast Ethernet Adapters User’s Guide

Stock Number: 511472-00, Rev. A

Page: 4-25

Print Spec Number: 496708-00

 

Current Date: 5/5/97

ECN Date: 5/97

Image 53
Contents PCI Ethernet and Fast Ethernet Adapters Technical and Product Support Adaptec Technical Support and ServicesElectronic Support Class a Device Certification Statements Sales and Ordering InformationClass B Device Certification Statements Page Page Getting Started Installing Network Drivers Using Emdiag to Troubleshoot Problems Cables System Requirements Getting StartedAdvisories What You Need to KnowConventions Fast Ethernet Ultimate Combo Adapter 10/100 Autosensing ModelsQuartet Adapters Before You Begin Installing the AdapterPage PCI Interrupts PCI Bios SettingsPCI-to-PCI Bridge Chip Configuring Quartet AdaptersTesting the Quartet Configuration Testing the PCI ConfigurationPCI Ethernet and Fast Ethernet Adapters Cable Requirements Connecting to Your Network CableConnector 10Mbps 100Mbps Cable Pins Pinout and Color Requirements Following chart provides cable pinout and color informationConnecting the Quartet Connecting the CableTwisted Pair Crossove Crossover CablesLink Status L.S Diagnostic LEDsRun Emdiag Checking the Connection with EmdiagPage Full Duplex Support Installation Instructions and Optional KeywordsDriver Naming Conventions PCI Ethernet and Fast Ethernet Adapters NetWare Installing and Configuring the Standard Driver for NetWareUsing the Inetcfg utility PCI Ethernet and Fast Ethernet Adapters Select Half Duplex or Full Duplex mode Installing the Duralink Driver for NetWareLoad Cdtdmi Load Failmib Enabling Snmp AgentsLoad Cdtdmi Manual InstallationLoad Failmib Manual Installation Automated NetWare Client InstallationLink Driver Empci DOS ODI ParametersWindows NT Installing the Standard Driver for Windows NTAdding Standard Drivers Remove Existing Adaptec Ethernet DriversConfiguring the Drivers Thin Installing the Duralink Driver for Windows NTAdding Duralink Drivers Configuring the Drivers Configuring the Primary and Backup Ports Snmp Management Station Windows 95 Driver Parameters Windows 95 Installation for PCIWindows Windows for Workgroups Windows for Workgroups Driver Parameters Ndis Installing With LAN ManagerNdis Driver Parameters IBM OS/2 SMP Installing with LAN ServerInstalling the Drivers for a Pre-existing OS/2 SMP Installing OS/2 SMP for the First Time Editing Driver Parameters SCO OpenServer Installing the SCO OpenServer DriverUnix Drivers Configuring the SCO OpenServer Driver SCO Unixware SMP Installing the DriversEMPCI0 EMPCI1 EMPCI2 EMPCI3 Configuring the IP AddressesDo you want to set this machine as a gateway?y/no/ unchanged Using Emdiag to Troubleshoot Problems Emdiag PCI Main Menu Using Emdiag for PCI AdaptersRunning Emdiag Configuration Status Diagnostics Running Remote Diagnostics PCI Device Information Quartet Device Information Isolating Faulty Hardware TroubleshootingReadme Viewer Technical Support InformationUse the following table to help answer common questions Frequently Asked QuestionsPage ANA-6901 and ANA-6901 Combo Adapter SpecificationsANA-6904 and ANA-6904BNC Quartet ANA-6910/FX ST and ANA-6910/FX SC ANA-6910/TX PCI ANA-6911/T4 and ANA-6911/T4 Combo PCI ANA-6911A/TX and ANA-6911A/TX Combo PCI ANA-6911/UC Ultimate Combo ANA-6940/Quartet TX ANA-6944A/TX Quartet ANA-6944/T4/Quartet Straight-through Cable Twisted Pair Cable TypesCrossover Cable Following tables provide cable pinout and color information Pinout and Color RequirementsPin PCI Index Index-3