Pyramid Technologies 4000HD manual Bell SET-UP

Page 4

the unit off a generator/inverter, use the UP or DOWN key to change the TIME STD to CRYSTAL which will cause the unit to keep time using an internal device.)

5. OFF- Unit will not adjust time for daylight saving time.

DSPLY FMT=AM/PM – Selects how the time will be displayed on the front of the unit. Using the UP or DOWN keys, select one of the following options:

1.AM/PM - Standard time (1-12 hours).

2.MIL - Military time (0-23 hours).

PRINT FMT=AM/PM – Selects how time will be printed on the time card. Using the UP or DOWN keys, select one of the following options:

1.AM/PM - Standard time (default setting) (i.e. 3:30 PM).

2.MIL- Military time (i.e. 3:30 PM = 15:30).

3.ATAAP-Military time with minutes expressed in hundredths of hour (i.e. 3:30 PM = 15.50).

SET HOUR – Sets the current hour of day by using the UP or DOWN key.

SET MINUTES – Sets the current minute of day by using the UP or DOWN key.

BELL SET-UP

The internal buzzer is intended for quiet areas. To adjust the volume of the internal buzzer, open the front cover and turn volume control on the left side of the circuit board clockwise to increase volume or counter clockwise to decrease volume.

External bells or buzzers can be added by purchasing a Model 5300 Bell Ringer. The Bell Ringer can ring up to 15 bells or horns with 50 events. Please refer to Optional Supplies and Accessories table located at the end of this booklet. To connect the 5300 Bell Ringer to the 4000/4000HD Time Recorder, plug the RJ-45 cable into jack on the left side of the Time Recorder. Connect the other end of the cable to the Model 5300. The wall transformer provided with the 5300 must be connected to the recepticle labeled POWER. Wire your bells/ horns to the labeled terminals on the 5300. The Bells/Horns must be wired in parallel as shown, not in series:

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model 4000/4000HD Programming the 4000/4000HD SET-UP Instructions UnpackingReady to GO Feature Table Bell SET-UP SET Event # no Page Page Page Time Cards Troubleshooting Changing the Print RibbonPage Frequently Asked Questions Supplies and Optional Accessories Limited WarrantyExtended Warranty Specifications Operating ConditionsPower Failure Pyramid Technologies, LLC Elm St. Meriden, CTPyramid Instrucciones Para Instalacion Paso 1 Desembalar Paso 2 Programar EL 4000/4000HDPaso 3 Listo Para Usar Tabla DE CaracteristicasAbajo Programación DE LA Campana Programación DE Evento # noPage Page Page Page Tarjetas DE Tiempo Cambiando LA Cinta de ImpresionTarjeta SIN LA Impresion O UN Mensaje DE Error Localizacion DE FallasPage Preguntas Comunes El No. de Cantidad La descripción Artículo Pyramid Technologies, LLC Elm Street. Meriden, CT La Garantía LimitadaEspecificaciones Dimensiones Condiciones de FuncionamientoCorte de Energia CalendarioPyramid 4000/4000HD Troisieme Etape Pret a Fonctionner Deuxieme Etape Programmer LE Modele 4000/4000HDInventaire DES Fonctions Page Configuration DE LA Sonnerie SET Event # no Page RST=16th & 1st 16e et 1er jour du mois Page Fiches DE Presence Changement DE LA Cartouche D’IMPRESSION Card Feeds with no Print or Error Message Conseils DE DepannageFoire AUX Questions Page Pieces DE Remplacement ET Accessoires Optionnels Garantie Limitee Pyramid Technologies, LLC Elm St.Meriden, CTFiche signalétique Conditions d’utilisation Coupure de courantCalendrier Précision de l’horlogeEs wird empfohlen, diese Anleitung aufzubewahren Inbetriebnahme Schritt 1 AuspackenSchritt 3 Stempeln Schritt 2 DAS Programmieren DES 4000/4000HDEinstellungstabelle Page Einrichten DES Akustischen Signals Ereignisnummer EinstellenSelect Page Page Page Stempelkarten Farbbandwechsel Fehlersuche Häufig Gestellte Fragen Zubehör Bestell.-NrMenge Beschreibung Garantie Technische Daten BetriebsbedingungenStromausfall KalenderGenauigkeitsabweichung der Uhr SpeicherkapazitätElm Street, Meriden, CT I2073 Rev a
Top Page Image Contents