4. Select the Wireless Setting and Installation option.
•Install Now: If you have already set up the wireless network, click this button to install the machine’s driver to use the wireless network machine. If you have not set up the wireless network, click the Wireless Setting and Installation button to set up the wireless network before you click this button.
•Wireless Setting and Installation: Configure the wireless network settings of your machine with a USB cable then install the machine driver. This is only for users who have not set up the wireless connection before.
5.Read the License Agreement, and select I accept the terms of the License Agreement. Then, click Next.
6.The software searches the wireless network.
If the search has failed, you may check if the USB cable is properly connected between the computer and machine, and follow the instructions on the window.
7.After searching, the window shows the wireless network devices. Select the name (SSID) of the access point you are using and click Next.
If you cannot find the network name you want to choose, or if you want to set the wireless configuration manually, click Advanced Setting.
•Enter the wireless Network Name: Enter the SSID of access point you want (SSID is
•Operation Mode: Select Infrastructure.
•Authentication: Select an authentication type.
Open System: Authentication is not used, and encryption may or may not be used, depending on the need for data security.
Shared Key: Authentication is used. A device that has a proper WEP key can access the network.
WPA Personal or WPA2 Personal: Select this option to authenticate the print server based on WPA
•Encryption: Select the encryption (None, WEP64, WEP128, TKIP, AES, TKIP AES).
•Network Key: Enter the encryption network key value.
•Confirm Network Key: Confirm the encryption network key value.
•WEP Key Index: If you are using WEP Encryption, select the appropriate WEP Key Index.
The wireless network security window appears when the access point has security settings.
The wireless network security window appears. The window may differ according to its security mode: WEP, or WPA.
•WEP
Select Open System or Shared Key for the authentication and enter the WEP security key. Click Next.
WEP (Wired Equivalent Privacy) is a security protocol preventing unauthorized access to your wireless network. WEP encrypts the data portion of each packet exchanged on a wireless network using a
•WPA
Enter the WPA shared key and click Next.
WPA authorizes and identifies users based on a secret key that changes automatically at regular intervals. WPA also uses TKIP (Temporal Key Integrity Protocol) and AES (Advanced Encryption Standard) for data encryption.
8.The window shows the wireless network settings and checks if the settings are correct. Click Next.
•For the DHCP method
If the IP address assignment method is DHCP, check if DHCP is shown in the window. If it shows Static, click Change TCP/IP to change the assignment method to DHCP.
•For the Static method
If the IP address assignment method is Static, check if Static is shown in the window. If it shows DHCP, click Change TCP/IP to enter the IP address and other network configuration values for the machine. Before entering the IP address for the machine, you must know the computer’s network configuration information. If the computer is set to DHCP, you must contact the network administrator to get the static IP address.
For example:
If the computer’s network information is as shown below:
-IP address: 169.254.133.42
-Subnet Mask: 255.255.0.0
Then, the machine’s network information should be as follows:
-IP address: 169.254.133.43
-Subnet Mask: 255.255.0.0 (Use the computer’s subnet mask.)
-Gateway: 169.254.133.1
9.When the wireless network setting is completed, disconnect the USB cable between the computer and machine. Click Next.
10.The Wireless Network Setting Complete window appears.
Select Yes if you accept the current settings and continue the setup procedure.
Select No if you want to return to the beginning screen. Then, click Next.
11.Click Next when the Confirm Printer Connection window appears.
12.Select the components to be installed. Click Next.
13.After selecting the components, you can also change the machine name, set the machine to be shared on the network, set the machine as the default machine, and change the port name of each machine. Click Next.
14.After the installation is finished, a window asking you to print a test page appears. If you want to print a test page, click Print a test page.
Otherwise, just click Next and go to step 16.