Sanyo srt-6000 Normal Recording, Concerning the Number of Times Tapes can be Rerecorded on

Page 15

NORMAL RECORDING

Concerning the Number of Times Tapes can be Rerecorded on

Depending on the recording speed mode, the tape must be replaced after a certain number of recording times.

Refer to the table below for the maximum number of times a tape can be recorded on.

Recording speed mode		Maximum number of
(hour mode)		recording times
		(with a standard grade
		tape)
6,	8	100

18,	24	50

30,	40	50

NOTES:

œThe maximum number of recording times will vary depending on the location and kind of tape used. Verify the recording quality and replace the tape when the quality starts to deteriorate.

The maximum number of recording times indicated above are based on test tapes (T-120 and T-160) used by the company.

œIf using longer tapes (i.e. T-180) the tape travel will not be as stable and that may cause problems.

Changes to the Recording Speed Mode During Recording

It is possible to permit or prevent changing the recording speed mode during recording.

1Press the MENU button until the (SET UP 4) menu is displayed.

@@@@@@@<SET@UP@4>

öSW@OUT

@@FIELD@@@@@@@@@01

@@TIMING@@@@@@@@FIELD

@@8H@@@@@@@@@@@@Y

öTHREAD@CHECK@@@Y

öVIDEO@LOSS@@@@@N

öREC@SPEED@@@@@@N

öEJECT@SET

@@EJECT@MODE@@@@EJECT1

@@OPERATION@@@@@SLAVE

2Turn the JOG dial, until the “REC SPEED” setting is flashing.

3Turn the SHUTTLE ring, to set the desired mode.

Y . . . . . . . . . . Recording speed mode can be changed

N. . . . . . . . . . Recording speed mode can not be changed

4Press the SEARCH button to save the setting.

Action to Take when the Video Signal Deteriorates

If there is no video signal during recording, fast forward, rewind modes, when in stop mode or when a tape is not loaded the menus are not displayed, “VIDEO LOSS” can be displayed on-screen and a signal (0 V) can be output at the ALARM OUT terminal. If in the (SET UP 2) menu, in the BUZZER section WARNING is set to “Y”, the buzzer will be heard. To stop the buzzer, press the STOP button.

1Press the MENU button until the (SET UP 4) menu is displayed.

2Turn the JOG dial, until the “VIDEO LOSS” setting is flashing.

3Turn the SHUTTLE ring, to set the desired mode.

N. . . . . . . . . . The video loss warning is not active.

Y . . . . . . . . . . The video loss warning is active.

4Press the SEARCH button to save the setting.

14

English

Image 15

Contents SRT-6000 Precautions Features AccessoryContents Search button Counter Reset buttonFront Panel TRACKING/V. Still or + buttonOFF indicator Locations of Controls and IndicatorsOperation Indicators Operation Mode IndicatorRS485 B Back PanelPower Cord Installation About the memory resetConnections Reference pages are shown in square brackets Types of ON-SCREEN Displays and Display SequenceShuttle ring Using the JOG dial and Shuttle ringTypes of ON-SCREEN Displays and Display Sequence JOG dialLast 2 digits only are displayed Setting the Language and ClockSetting procedure is now completed Day of week is set automaticallyDate and time are displayed Changing the ON-SCREEN DisplaySelecting the On-screen Display Changing the Date/Time Display PositionVideo Cassette Tapes Setting the Action to Take When a Cassette is Loaded Video Cassette TapesCorrect tape thread check function Record Pause Recording Speed ModeNormal Recording Normal Recording Before startingConcerning the Number of Times Tapes can be Rerecorded on Changes to the Recording Speed Mode During RecordingAction to Take when the Video Signal Deteriorates Normal RecordingClog Detection Recording CheckAutorepeat Recording Setting the Mode at the End of the TapeRepeat indicator will light Alarm Mode setting is flashingAlarm Recording Setting Alarm RecordingChecking the Alarm Recordings Time Alarm RecordingAlarm Recording Counter Display Connections to the Alarm IN/OUT TerminalsAlarm Scan Alarm SearchRecording will not take place Program Timer RecordingDay of the week of the 8th line is flashing Program Timer RecordingTo Cancel all Program Timer Recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer RecordingThese portions will not be recorded Recording Using AN External Timer Input Series recording connections Series Recording SetupRepeat REC switch Series RecordingContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Normal Playback Special Playback D Search 01 0000 will be displayed on screen Special PlaybackDay/Time Search Shuttle Ring OperationIs displayed on the digital display Setting the Security LockCounter will be reset to 0H 00M 00S Tape CounterSetting the Buzzer Clock AdjustmentSetting procedure on the first VCR is now completed Eject in terminal Setting the Cassette Eject ModeCassette Eject Setup Eject terminal connectionSetting the RS-232C or RS-485 Data Transfer Speed DIP Switches SetupData Transfer Speed Setup RS-485 Connection Setting the RS-232C or RS-485 Data Transfer SpeedRS485 RJ-11 connector layout Connector a Connector B SignalTape END OUT Terminal Timer OUT TerminalTape END OUT Terminal Output Setting Output TerminalsOutput Terminals Series OUT/NON REC OUT terminal settingSW OUT Terminal Output Setting Field or Frame setting is flashingRemote Jack Remote control settingMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyRC4QR/U2