Sanyo srt-6000 instruction manual Autorepeat Recording, Setting the Mode at the End of the Tape

Page 17

AUTOREPEAT RECORDING

Autorepeat Recording

The same tape can be recorded over many times.

œFollow the Before starting steps, under “NORMAL RECORDING”.

1Set the REPEAT REC switch to the “ON” position.

øThe REPEAT indicator will light.

2Press the MENU button until the (SET UP 3) menu is displayed.

øThe “ALARM MODE” setting is flashing.

@@@@@@@<SET@UP@3>

öALARM@MODE@@@@@@@Y1

öALARM@DURATION@@@20S

öVERTICAL@SYNC@@@@Y

öEXT@TIME@ADJ.@@@@01:00

öTAPE@IN@MODE@@@@@STOP

öTAPE@END@MODE@@@@R1 öTAPE@END@OUT@@@@@-3M öCLOG@DETECT.@@@@@Y öSERIES@REC@IN@@@@N öRS-232C@@@@@@@@@@19200

3Turn the JOG dial, until the “TAPE END MODE” setting is flashing.

4Turn the SHUTTLE ring to set to “R 1” or “R 2”. (See “Setting the Mode at the End of the Tape”)

5Press the SEARCH button to save the setting.

øThe setting procedure is now completed.

6Press the REC/PLAY SPEED l (or j) button to set the recording speed mode.

7Press the REC button.

øRecording will start. When the tape end is reached, the VCR will rewind it to the beginning, and recording will resume.

øWhen the end of the tape is reached, a buzzer will be heard (if in the (SETUP 2) menu, in the BUZZER section TAPE END is set to “Y”) and “OFF” will be displayed until the rewinding operation starts.

NOTES:

œIf during autorepeat recording there is an alarm trigger, “AL” is displayed on the digital display and alarm recording will take place. (Please refer to page 17, “ALARM RECORDING”.)

œIf the “TAPE END MODE” setting is R 1, the REPEAT indicator will go off if there is an alarm trigger. The recording will continue to the end of the tape then it will be rewound to the beginning and stop. “OFF” will be displayed on the digital display. To turn off the buzzer (if in the (SETUP 2) menu, in the BUZZER section TAPE END is set to “Y”) and the “OFF” display, press the STOP, EJECT or PLAY button, or turn the SHUTTLE ring.

œIf “AL” is displayed on the digital display and the “TAPE END MODE” setting is R1, autorepeat recording is not possible.

Setting the Mode at the End of the Tape

In the (SET UP 3) menu, you can set the mode of the VCR mode when the tape reaches the end during recording.

1Press the MENU button until the (SET UP 3) menu is displayed.

@@@@@@@<SET@UP@3>

öALARM@MODE@@@@@@@Y1

öALARM@DURATION@@@20S

öVERTICAL@SYNC@@@@Y

öEXT@TIME@ADJ.@@@@01:00

öTAPE@IN@MODE@@@@@STOP

öTAPE@END@MODE@@@@REW öTAPE@END@OUT@@@@@-3M öCLOG@DETECT.@@@@@Y öSERIES@REC@IN@@@@N öRS-232C@@@@@@@@@@19200

2Turn the JOG dial, until the “TAPE END MODE” setting is flashing.

3Turn the SHUTTLE ring, to set the desired mode.

œSetting when the REPEAT REC switch is set to the “OFF” position.

REW. . . . . . . Rewinds the tape to the beginning, then goes to stop mode

STOP . . . . . . Goes to stop mode EJECT . . . . . The cassette is ejected

œSetting when the REPEAT REC switch is set to the “ON” position.

R1. . . . . . . . . Autorepeat recording mode is automatically canceled if there was an alarm trigger

R2. . . . . . . . . Autorepeat recording mode is active even if there was an alarm trigger

4Press the SEARCH button to save the setting.

16

English

Page 16 Page 18
Image 17
Page 16 Page 18
Contents SRT-6000 Precautions Contents FeaturesAccessory Front Panel Counter Reset buttonTRACKING/V. Still or + button Search buttonOperation Indicators Locations of Controls and IndicatorsOperation Mode Indicator OFF indicatorRS485 B Back PanelConnections Power Cord InstallationAbout the memory reset Reference pages are shown in square brackets Types of ON-SCREEN Displays and Display SequenceTypes of ON-SCREEN Displays and Display Sequence Using the JOG dial and Shuttle ringJOG dial Shuttle ringSetting procedure is now completed Setting the Language and ClockDay of week is set automatically Last 2 digits only are displayedSelecting the On-screen Display Changing the ON-SCREEN DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Normal Recording Recording Speed ModeNormal Recording Before starting Record PauseAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingNormal Recording Concerning the Number of Times Tapes can be Rerecorded onClog Detection Recording CheckRepeat indicator will light Setting the Mode at the End of the TapeAlarm Mode setting is flashing Autorepeat RecordingAlarm Recording Setting Alarm RecordingAlarm Recording Counter Display Alarm RecordingConnections to the Alarm IN/OUT Terminals Checking the Alarm Recordings TimeAlarm Scan Alarm SearchRecording will not take place Program Timer RecordingDay of the week of the 8th line is flashing Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Repeat REC switch Series Recording SetupSeries Recording Series recording connectionsLoop recording connection example with 2 VCRs Continous Loop Recording SetupSeries Recording Normal Playback Special Playback Day/Time Search Special PlaybackShuttle Ring Operation D Search 01 0000 will be displayed on screenCounter will be reset to 0H 00M 00S Setting the Security LockTape Counter Is displayed on the digital displaySetting procedure on the first VCR is now completed Setting the BuzzerClock Adjustment Cassette Eject Setup Setting the Cassette Eject ModeEject terminal connection Eject in terminalData Transfer Speed Setup Setting the RS-232C or RS-485 Data Transfer SpeedDIP Switches Setup RS485 RJ-11 connector layout Setting the RS-232C or RS-485 Data Transfer SpeedConnector a Connector B Signal RS-485 ConnectionTape END OUT Terminal Output Setting Timer OUT TerminalOutput Terminals Tape END OUT TerminalSW OUT Terminal Output Setting Series OUT/NON REC OUT terminal settingField or Frame setting is flashing Output TerminalsRemote Jack Remote control settingMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyRC4QR/U2
Top Page Image Contents