Sanyo srt-6000 instruction manual Remote Jack, Remote control setting

Page 38

OUTPUT TERMINALS

REMOTE Jack

You can use a VA-RMN01 Remote Control Unit (sold separately) to control remotely the VCR.

NOTE:

œThe functions not available on the VCR will not operate.

Remote control of the VCR is possible by connecting a remote controller with a circuit such as indicated below, to the REMOTE jack.

NOTES:

œUse a 3.5 mm mini-jack type plug.

œThe connection should be done using a shielded cable no more than 5 meters long.

œThe functions not available on the VCR will not operate.

Remote control circuit

Remote control setting

The remote control switch 7 can be set to either eject the tape or access the menus.

1Press the MENU button until the (SET UP 1) menu is displayed.

@@@@@@@<SET@UP@1>

öDAYLIGHT@SET@@@@@USE

@@@@@@@@WEEK@MONTH@TIME

@ON@@@1ST-SUN@@04@02:00 @OFF@@LST-SUN@@10@02:00 öOUTPUT@@@@@@@@SERIES öCLOCK@SET @10-15-99@FRI@@15:20:00 öREMOTE@@@@@@@@EJECT öLANGUAGE-LANGUE-IDIOMA

@@@ENGLISH

2Turn the JOG dial, until the “REMOTE” setting is flashing.

3Turn the SHUTTLE ring, to select the desired switch mode.

EJECT . . . . . Switch 7 will eject the tape. MENU . . . . . Switch 7 will display the menu.

4Press the SEARCH button to save the setting.

R0 1.2K

R1 0.3K

R2 0.43K

R3 0.51K

R4 0.62K

R5 0.75K

R6 0.91K

R7 1.1K

R8 1.3K

R9 2.0K

R10 2.4K

R11 3.6K

R12 5.6K

The resistance tolerance is 2% or less.

SW0: EJECT

SW1: STOP

SW2: STILL/PAUSE

SW3: REW

SW4: FF

SW5: PLAY

SW6: REC

SW7: EJECT (or MENU)

SW8: REV

SW9: REC/PLAY SPEED j, j

SW10: REC/PLAY SPEED l, l

SW11: SHIFT ], »

SW12: SHIFT «, «

English

37

Image 38

Contents SRT-6000 Precautions Contents FeaturesAccessory TRACKING/V. Still or + button Counter Reset buttonFront Panel Search buttonOperation Mode Indicator Locations of Controls and IndicatorsOperation Indicators OFF indicatorBack Panel RS485 BConnections Power Cord InstallationAbout the memory reset Types of ON-SCREEN Displays and Display Sequence Reference pages are shown in square bracketsJOG dial Using the JOG dial and Shuttle ringTypes of ON-SCREEN Displays and Display Sequence Shuttle ringDay of week is set automatically Setting the Language and ClockSetting procedure is now completed Last 2 digits only are displayedChanging the Date/Time Display Position Changing the ON-SCREEN DisplaySelecting the On-screen Display Date and time are displayedVideo Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Normal Recording Before starting Recording Speed ModeNormal Recording Record PauseNormal Recording Changes to the Recording Speed Mode During RecordingAction to Take when the Video Signal Deteriorates Concerning the Number of Times Tapes can be Rerecorded onRecording Check Clog DetectionAlarm Mode setting is flashing Setting the Mode at the End of the TapeRepeat indicator will light Autorepeat RecordingAlarm Recording Alarm Recording SettingConnections to the Alarm IN/OUT Terminals Alarm RecordingAlarm Recording Counter Display Checking the Alarm Recordings TimeAlarm Search Alarm ScanProgram Timer Recording Recording will not take placeProgram Timer Recording Day of the week of the 8th line is flashingTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Series Recording Series Recording SetupRepeat REC switch Series recording connectionsLoop recording connection example with 2 VCRs Continous Loop Recording SetupSeries Recording Normal Playback Special Playback Shuttle Ring Operation Special PlaybackDay/Time Search D Search 01 0000 will be displayed on screenTape Counter Setting the Security LockCounter will be reset to 0H 00M 00S Is displayed on the digital displaySetting procedure on the first VCR is now completed Setting the BuzzerClock Adjustment Eject terminal connection Setting the Cassette Eject ModeCassette Eject Setup Eject in terminalData Transfer Speed Setup Setting the RS-232C or RS-485 Data Transfer SpeedDIP Switches Setup Connector a Connector B Signal Setting the RS-232C or RS-485 Data Transfer SpeedRS485 RJ-11 connector layout RS-485 ConnectionOutput Terminals Timer OUT TerminalTape END OUT Terminal Output Setting Tape END OUT TerminalField or Frame setting is flashing Series OUT/NON REC OUT terminal settingSW OUT Terminal Output Setting Output TerminalsRemote control setting Remote JackMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeRC4QR/U2