Sanyo srt-6000 instruction manual Troubleshooting Guide, After a Power Failure, System Down

Page 41

TROUBLESHOOTING GUIDE

If the unit does not operate normally when you follow the instructions indicated in the manual, please refer to the table below.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

 

 

 

No power

The power cord is not connected

Connect the power cord

No image displayed on

The connections are not correct

Check that all connections are correct

the monitor TV

 

 

The power to the camera and/or monitor TV

Turn all connected devices power on

 

is not turned on

 

 

 

 

The buttons do not

A cassette tape is not loaded

Load a cassette and turn the power on

respond

 

 

All functions are suspended due to

Wait for the “À” indicator to go off

 

condensation

 

 

Alarm recording

Wait for the alarm recording to end

 

The security lock is engaged

Cancel the security lock

Recording is not

The loaded cassette has no

Load a cassette tape with

possible (the tape is

erasure-prevention tab

erasure-prevention tab or cover the tab hole

ejected)

 

with adhesive tape

Autorepeat recording is

“AL” is displayed on the digital display

Display (ALARM TIME) menu, then press

not possible

 

the MENU RESET button to turn off the “AL”

 

 

indicator

Timer recording is not

The date and time are not set correctly

Set the date and time correctly

possible

The unit is not set to timer recording

Press the TIMER button to display “n” on

 

stand-by mode

the digital display

 

“N” is selected for the timer recordings

Be sure to select “Y” for the programmed

 

 

timer recordings

Alarm recording is not

“OFF” is displayed on the digital display

Press the EJECT, STOP or PLAY button or

possible

 

turn the SHUTTLE ring to turn the indicator

 

 

off

 

 

 

Noise in the playback

The video heads need cleaning

Clean the video heads

picture

 

 

 

 

 

The date and time are

The ON SCREEN switch is set to the “OFF”

Set the ON SCREEN switch to the “ON”

not recorded

position

position

 

 

 

The cassette tape

Problem with the system

Unplug the power cord then plug it back in

cannot be ejected

 

 

The cassette is ejected

The tape is not threaded correctly

Try inserting the cassette one more time or

a few seconds after it

 

using a new cassette. If it is ejected again,

has been inserted

 

please consult your dealer.

 

 

 

After a Power Failure

If after a power failure the recording speed is reset to 8-hour mode, it is due to insufficient backup battery charge. This is not a malfunction.

System Down

If the unit does not function at all, try the following.

1Unplug the power cord then plug it back in.

2Reset the memory. (Press the ALL RESET button. Under normal conditions, do not touch the ALL RESET button.)

3If the problem is not corrected after performing steps 1 and 2 a few times, consult your dealer.

40

English

Page 40 Page 42
Image 41
Page 40 Page 42
Contents SRT-6000 Precautions Contents FeaturesAccessory Front Panel Counter Reset buttonTRACKING/V. Still or + button Search buttonOperation Indicators Locations of Controls and IndicatorsOperation Mode Indicator OFF indicatorRS485 B Back PanelConnections Power Cord InstallationAbout the memory reset Reference pages are shown in square brackets Types of ON-SCREEN Displays and Display SequenceTypes of ON-SCREEN Displays and Display Sequence Using the JOG dial and Shuttle ringJOG dial Shuttle ringSetting procedure is now completed Setting the Language and ClockDay of week is set automatically Last 2 digits only are displayedSelecting the On-screen Display Changing the ON-SCREEN DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Normal Recording Recording Speed ModeNormal Recording Before starting Record PauseAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingNormal Recording Concerning the Number of Times Tapes can be Rerecorded onClog Detection Recording CheckRepeat indicator will light Setting the Mode at the End of the TapeAlarm Mode setting is flashing Autorepeat RecordingAlarm Recording Setting Alarm RecordingAlarm Recording Counter Display Alarm RecordingConnections to the Alarm IN/OUT Terminals Checking the Alarm Recordings TimeAlarm Scan Alarm SearchRecording will not take place Program Timer RecordingDay of the week of the 8th line is flashing Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Repeat REC switch Series Recording SetupSeries Recording Series recording connectionsLoop recording connection example with 2 VCRs Continous Loop Recording SetupSeries Recording Normal Playback Special Playback Day/Time Search Special PlaybackShuttle Ring Operation D Search 01 0000 will be displayed on screenCounter will be reset to 0H 00M 00S Setting the Security LockTape Counter Is displayed on the digital displaySetting procedure on the first VCR is now completed Setting the BuzzerClock Adjustment Cassette Eject Setup Setting the Cassette Eject ModeEject terminal connection Eject in terminalData Transfer Speed Setup Setting the RS-232C or RS-485 Data Transfer SpeedDIP Switches Setup RS485 RJ-11 connector layout Setting the RS-232C or RS-485 Data Transfer SpeedConnector a Connector B Signal RS-485 ConnectionTape END OUT Terminal Output Setting Timer OUT TerminalOutput Terminals Tape END OUT TerminalSW OUT Terminal Output Setting Series OUT/NON REC OUT terminal settingField or Frame setting is flashing Output TerminalsRemote Jack Remote control settingMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyRC4QR/U2
Top Page Image Contents