Sanyo srt-6000 Setting the RS-232C or RS-485 Data Transfer Speed, DIP Switches Setup

Page 34

SETTING THE RS-232C OR RS-485 DATA TRANSFER SPEED

The VCR can be controlled by a computer connected to the RS-232C connector. It can also be controlled through a special controller connected to the RS-485 connector.

You must specify which connector (RS-232C or RS-485) is used. (Refer to “Data Transfer Speed Setup.”)

DIP Switches Setup

The DIP switches need to be set when a computer, special controller, etc. connected to the RS-232C or RS-485 connectors is used to control the VCR. Make sure to turn the VCR power off before setting the DIP switches.

ADDRESS 485 TERMINATE

ON ON

ON

1 2 3 4 5 6 7 8 9 10

OFF OFF 232

SW No.

1-7: To setup the VCR address (only when using the

œSwitch 1 is the least significant bit (LSB) and

switch 7 the most significant bit (MSB) (Down: 0,

Up: 1)RS-485 connector).

Example:

œIf the address is 1, set switch 1 to the ON side (up)

œIf the address is 10, set switches 2 and 4 to the ON side (up)

œIf the address is 127, set all the switches to the ON side (up)

8:Available (Not used)

9:To select the connector used. [232] side (down) for RS-232C, [485] side (up) for RS-485.

10:To setup the termination (only when using the RS-485 connector).

OFF side (down): Not terminated

ON side (up): Terminated

NOTE:

œRefer to the RS-232C and RS-485 command section or to the special controller and/or to the computer instruction manual.

Data Transfer Speed Setup

1Press the MENU button until the (SET UP 3) menu is displayed.

@@@@@@@<SET@UP@3>

öALARM@MODE@@@@@@@Y1

öALARM@DURATION@@@20S

öVERTICAL@SYNC@@@@Y

öEXT@TIME@ADJ.@@@@01:00

öTAPE@IN@MODE@@@@@STOP

öTAPE@END@MODE@@@@REW öTAPE@END@OUT@@@@@-3M öCLOG@DETECT.@@@@@Y öSERIES@REC@IN@@@@N öRS-232C@@@@@@@@@@19200

2Turn the JOG dial, until the “RS-232C” or “RS-485” setting is flashing.

NOTE:

œThe display will depend on the DIP switch 9 setting. When down “RS-232C” is displayed and when up “RS-485” is displayed.

3Turn the SHUTTLE ring to set the desired transfer speed.

192002400 48009600

4Press the SEARCH button to save the setting.

RS232C 9-pin connector layout

15

6 9

Pin

Signal

Operation

Signal direction

number

 

 

 

 

 

 

 

2

RXD

Receive

VCR ← Computer

data

 

 

 

 

 

 

 

3

TXD

Send data

VCR → Computer

 

 

 

 

7

RTS

Request

VCR → Computer

to send

 

 

 

 

 

 

 

5

GND

Signal

 

ground

 

 

 

 

 

 

 

 

The signal transmission is compatible with RS-232C specifications.

English

33

Page 33 Page 35
Image 34
Page 33 Page 35
Contents SRT-6000 Precautions Accessory FeaturesContents TRACKING/V. Still or + button Counter Reset buttonFront Panel Search buttonOperation Mode Indicator Locations of Controls and IndicatorsOperation Indicators OFF indicatorBack Panel RS485 BAbout the memory reset Power Cord InstallationConnections Types of ON-SCREEN Displays and Display Sequence Reference pages are shown in square bracketsJOG dial Using the JOG dial and Shuttle ringTypes of ON-SCREEN Displays and Display Sequence Shuttle ringDay of week is set automatically Setting the Language and ClockSetting procedure is now completed Last 2 digits only are displayedChanging the Date/Time Display Position Changing the ON-SCREEN DisplaySelecting the On-screen Display Date and time are displayedVideo Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedCorrect tape thread check function Normal Recording Before starting Recording Speed ModeNormal Recording Record PauseNormal Recording Changes to the Recording Speed Mode During RecordingAction to Take when the Video Signal Deteriorates Concerning the Number of Times Tapes can be Rerecorded onRecording Check Clog DetectionAlarm Mode setting is flashing Setting the Mode at the End of the TapeRepeat indicator will light Autorepeat RecordingAlarm Recording Alarm Recording SettingConnections to the Alarm IN/OUT Terminals Alarm RecordingAlarm Recording Counter Display Checking the Alarm Recordings TimeAlarm Search Alarm ScanProgram Timer Recording Recording will not take placeProgram Timer Recording Day of the week of the 8th line is flashingTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Series Recording Series Recording SetupRepeat REC switch Series recording connectionsSeries Recording Continous Loop Recording SetupLoop recording connection example with 2 VCRs Normal Playback Special Playback Shuttle Ring Operation Special PlaybackDay/Time Search D Search 01 0000 will be displayed on screenTape Counter Setting the Security LockCounter will be reset to 0H 00M 00S Is displayed on the digital displayClock Adjustment Setting the BuzzerSetting procedure on the first VCR is now completed Eject terminal connection Setting the Cassette Eject ModeCassette Eject Setup Eject in terminalDIP Switches Setup Setting the RS-232C or RS-485 Data Transfer SpeedData Transfer Speed Setup Connector a Connector B Signal Setting the RS-232C or RS-485 Data Transfer SpeedRS485 RJ-11 connector layout RS-485 ConnectionOutput Terminals Timer OUT TerminalTape END OUT Terminal Output Setting Tape END OUT TerminalField or Frame setting is flashing Series OUT/NON REC OUT terminal settingSW OUT Terminal Output Setting Output TerminalsRemote control setting Remote JackMaintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeRC4QR/U2
Top Page Image Contents