Memorex MVR4042 Ventilation, Power Sources, Grounding or Polarization, Lightning, Power Lines

Page 3

IMPORTANT SAFEGUARDS

9.VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation and to ensure reliable operation of the unit and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in built-in installations such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

10.POWER SOURCES

This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power com- pany. For units intended to operate from battery power, or other sources, refer to the operating instructions.

11.GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating- current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug If your unit is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin, this plug will only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.

Do not defeat the safety purpose of the grounding- type plug.

12.POWER-CORD PROTECTION Power-supply cords should be routed so that they

are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13.LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

14.POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

15.OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16.OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit as they may touch dangerous voltage points or short out parts that could result in fire or electric shock.

Never spill or spray any type of liquid into the unit.

17.OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

18.SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

ENGLISH

3

4F90701A/E COV-07

3

20/03/2003, 10:32

Image 3
Contents MVR4042 Retain Instructions CleaningAccessories Read InstructionsGrounding or Polarization Power SourcesPower Lines VentilationWall or Ceiling Mounting Damage Requiring ServiceReplacement Parts Safety CheckLocation and Handling PrecautionsPower Source Moisture CondensationEffective Distance of the Remote Control Precautions FeaturesBattery Cautions Battery InstallationTable of Contents Remote Control Location of ControlsFront PAUSE/STILL button During recording, this AC Power Cord Connect to a 120V 60Hz outletRear 3231UHF Basic ConnectionsAntenna to VCR Connection VCROhm Input Ohm outputs Ohm Coaxial Cable Not supplied VCR to TV Connection75/300 ohm outputs Ohm Coaxial Cable Not supplied Supplied SplitterCatv Cable TV Connections Allows Prevents Converter/Descrambler SwitchCable Descrambler Switch Splitter ConverterAUDIO/VIDEO Connections AUDIO/VIDEO ConnectionStereo Amplifier Connections Check Before YOU Begin Setting the Video ChannelSetting the Clock Language SelectionTV/CATV Selection To ADD/DELETE Channels Setting the ChannelsAutomatic Memory Tuning Noise EliminationPlayback Recording a TV Program Special PlaybackTo Prevent AN Accidental Recording To Stop RecordingTo Stop Recording Temporarily Recording ONE Program While Watching AnotherONE-TOUCH Timer Recording OTR Setting the Timer RecordingIntact. The VCR will automatically turn on ON-SCREEN Function Display Output Selection Stereo Recording and PlaybackSecond Audio Program SAP Recording Stereo BroadcastsDuplicating a Video Tape Video Head CleaningVideo Head Cleaning Make all connections before turning on the powerRecording Before Requesting ServiceSymptom Cause Possible Solution Power TV Broadcast ReceptionSymptom Cause Possible Solution Remote Control SpecificationsMemo Memo Siga LAS Instrucciones NotaLEA LAS Instrucciones Respete LAS AdvertenciasLineas DE Alimentacion VentilacionFuentes DE Alimentacion Tormentas ElectricasRevision DE Seguridad Servicio19. Daños QUE Requieran Reparacion Piezas DE RepuestoFuente DE Alimentacion PrecaucionesCondensacion DE Humedad Posicion Y ManejoCaracteristicas Precaucion CON LAS PilasInstalacion DE Pilas Indice Sistema automático de repetición de reproducciónPresentación de 3 idiomas en pantalla Usted Ubicacion DE LOS Controles Parte DelanteraControl Remoto Parte Trasera VHF UHF Conexiones BasicosConexion DE Antena a Videograbador VideograbadorTelevisor con entrada única de 75 ohmios para VHF/UHF Conexion DEL Videograbador a UN TelevisorPermite No Permite Conexiones DE TV Cable CatvDivisor InterruptorCordón AUDIO/VIDEO no incluido Conexiones DE AUDIO/VIDEOConexion DE AUDIO/VIDEO Conexion DEL Amplificacor EstereoConfirme Antes DE Empezar Ajuste DEL Canal DE VideoAjuste DEL Reloj Seleccion DE IdiomaSeleccion DE TV/CATV Ajuste DE CanalesEliminacion DE Ruido Borrado DE UN Canal DE LA MemoriaReproduccion Colocacion Y ExtraccionGrabacion DE UN Programa DE TV Reproduccion EspecialLa cinta Destornillador Lengüeta para evitar el borrado Para Detener LA GrabacionPara Grabar UN Programa Mientras SE VE Otro Para Detener Temporalmente LA GrabacionAjuste DE LA Grabacion POR Temporizador Cinta deseada SP o SLPVelocidad DE Cinta SLP Indicacion DE Funciones EN LA Pantalla Seleccion DE Salida Grabacion Y Reproduccion EstereofonicasSegundo Programa DE Sonido SAP Grabacion DE Emisoras EN EstereoDesgastadas Duplicacion DE UNA Cinta DE VideoLimpieza DE LA Cabeza DE Video Presione el botón de InputAntes DE Solicitar Servicio Control Remoto J4F90701A U 03/04