Klark Teknik DN9344E specifications Rear Panel DN9340E, Mains, Inputs a and B, Word clock Input

Page 21

Controls, Connectors, Indicators: DN9340E

4. REAR PANEL: DN9340E

		1			2	3	7	5	4	6	5	4


1		Mains					Mains inlet unit is auto sensing over the range 100-240V AC.
		inlet socket
2		Ethernet					2-port Ethernet switch for remote control using Cat-5
							cabling.

3RS-232 serial interface RS-232 serial interface for Solo Tracking System operation in association with MIDAS consoles.

4	Inputs A and B	Analogue – electronically balanced XLR audio input sockets
		Pinouts: Pin 1	Screen
		Pinouts: Pin 1	Screen
		Pin 2	Hot
		Pin 3	Cold

Digital – input A supports incoming 96kHz AES/EBU signals. Note that when digital input is selected, input B is inactive.

AES/EBU is 110 Ohms. Sample rate converters (SRCs) support incoming signals at sampling frequencies from 32kHz to 96kHz ± 12.5%, while allowing the unit to operate internally at 48kHz. An SRC bypass facility is available for 48kHz operation, to eliminate the propagation delay through the SRC.

Pinouts: Pin 1 Screen

Pin 2 Data +

Pin 3 Data -

5Analogue Outputs A Electronically balanced XLR audio output plugs and B

Pinouts: Pin 1 Screen

Pin 2 Hot

Pin 3 Cold

6Digital Outputs A and B Digital AES/EBU output for channels A and B. AES/EBU is 110 Ohms.

7	Word clock Input	A word clock input is provided for synchronisation purposes.

11

Image 21

Contents DN9340E/DN9344E Page Important Safety Instructions Page Declaration of Conformity Page Contents Setup Menu DN9340E Application Notes Page Safety Warning Installation ConsiderationsAfter Unpacking Page DN9340E Front Panel Quick ReferenceDN9344E Front Panel Key Features DN9340E & DN9344E Key FeaturesIntroducing the DN9340E/DN9344E Host Software VersionsSpace efficiency Remote control operationInterface to Midas consoles Store and Recall ParametersEQ Access and Displays Controls, Connectors, Indicators DN9340EFront Panel DN9340E Soft keys displaySelected channel both channels if linked. When a Bypass, Channel Select, Soft Keys and Alphanumeric DisplaySoft keys Touch Strip, Store and Recall, Home Setup and Data Entry PC Port, Metering and Power Mains Rear Panel DN9340EInputs a and B Word clock InputSignal Flow DN9340E Signal Flow DN9340EOperation DN9340E Operation DN9340EHome Home page sub-menusTouchstrip Operation on the Home Soft Key Functions Graphic EqualisationEQ Flat Automatic featuresGrouping Touchstrip operation with Graphic equalisationParametric Equalisation EQ remove Touchstrip operation with Parametric equalisationDynamic Equalisation Lo Threshold / LevelHi Threshold / Level Time constants Touchstrip operation with Dynamic equalisationFilters Create Filter functionFilter Type Left Encoder Centre Encoder Right Encoder Filter settings Touchstrip operation with FiltersFilter remove Metering Clear Down Sequence Setup Menu DN9340E Setup Menu DN9340ETo access the Set Up menu pages GeneralTo switch remote communications off Remote control via a PCComms channel To select a slave remote communications channelTo select a master remote communications channel Using a DN9340E for master controlTo select a slave communications channel To remove the unit from the networkFront Panel lock To set a Panel LockTo remove the Panel Lock To change the input source Analogue/Digital Input SelectTo set a Presets lock Presets lockDigital Output Clock Select To select the output clock sourceDelay options LCD contrast adjustmentNaming Pages 7 To enter a namePower-up Logo Ethernet Settings Pages 11Ethernet IP Address To check and edit the Subnet Mask Ethernet Subnet Mask SetupUsing the DN9340E Memories To store settingsTo recall settings Connections Remote ControlAddresses Data modelGetting started Setting the master unit on-lineOn a DN9340E On a DN9344ETo set up the names OperationSystem naming To set up the assignment Copy channel functionSolo Tracking operation Helix DN9340E/DN9344E unit interconnections OverviewConnecting the Helix DN9340/DN9344E units in a daisy chain Ethernet connection wireless option Ethernet ConnectionEthernet connection standard Configuring the DN9344E for Network Communication Configuring the DN9340E for Network CommunicationConnection and Configuration Procedure Serial Connection OptionSerial connection details Alphanumeric displays, SETUP, Metering and Power Controls, Connectors, Indicators DN9344EPress to step through the Set Up pages Power Switch Power on Power on indication Power indicationIndicators Indicators, Up and Down Buttons, PC Port and Scribble StripsMains inlet socket Rear Panel DN9344E1B, 2A and 2B InterfaceSignal Flow DN9344E Signal Flow DN9344EOperation DN9344E Operation DN9344ERemote Comms channels To select a remote communications channel To disable remote communications and relay operation To enable the Contact Closure Relay modeTo set a password PasswordTo change the settings for Inputs 1A and 1B Analogue/Digital Input Select Pages 3Digital Output Clock Select Pages 5 To change the settings for OutputSubnet Mask Ethernet SettingsTo change the IP address To change the Subnet MaskDynamic EQ Application NotesApplication Notes Application Notes What do we mean by all these Q types? Constant Q Proportional QSymmetrical Q What is AES/EBU? 17.1. DN9340E Technical Specification DN9340EPower Requirements 17.2. DN9344E Technical Specification DN9344ERelay Socket Pin D-type rear Power Pin IEC Service Information BatteryReplacement

Related manuals

Manual 65 pages 57.17 Kb