Klark Teknik DN9340E, DN9344E specifications Serial Connection Option, Serial connection details

Page 54

Remote Control

10.4. Serial Connection (Option)

There is an option to control your system remotely from a laptop/ PC via the RS-232 connection (the “PC PORT”) on the front panel of the first HELIX DN9340E/DN9344E unit. It is possible to connect to other HELIX DN9340E/DN9344E units from the rear Ethernet port(s) when using a serial connection, but note that this will be slower than using Ethernet.

10.4.1Serial connection details

The system set up for serial connection is illustrated below.

10.4.2Connection and Configuration Procedure

The HELIX RCS laptop/PC is connected to the daisy chain as follows:

To connect, set up and configure your system for serial operation

1Connect the HELIX DN9340E/DN9344E units in a daisy chain configuration, see Section 10.2.1.

2Power up the HELIX DN9340E/DN9344E units and assign each one a unique Comms channel, as described in Sections 7.2 and 15.2.

Note

The order of the addresses does not need to mirror the order of the daisy chain networking, but each unit MUST have a unique comms channel address.

3Referring to the following table, connect your laptop/PC to the first HELIX unit in the daisy chain.

HELIX DN9340E Unit	Laptop/PC	Cable/Converter Required
Connection	Connection

RS-232 input to front panel	D9 COM port	Host cable
“PC PORT”
	USB port	KK systems USB/232 converter plus host cable
		For details of converters plese refer to
		http://www.klarkteknik.com/faq_connections.htm

44

Image 54

Contents DN9340E/DN9344E Page Important Safety Instructions Page Declaration of Conformity Page Contents Setup Menu DN9340E Application Notes Page Safety Warning Installation ConsiderationsAfter Unpacking Page Quick Reference DN9340E Front PanelDN9344E Front Panel Introducing the DN9340E/DN9344E DN9340E & DN9344E Key FeaturesKey Features Host Software VersionsInterface to Midas consoles Remote control operationSpace efficiency Store and Recall ParametersFront Panel DN9340E Controls, Connectors, Indicators DN9340EEQ Access and Displays Soft keys displaySelected channel both channels if linked. When a Bypass, Channel Select, Soft Keys and Alphanumeric DisplaySoft keys Touch Strip, Store and Recall, Home Setup and Data Entry PC Port, Metering and Power Inputs a and B Rear Panel DN9340EMains Word clock InputSignal Flow DN9340E Signal Flow DN9340EHome Operation DN9340EOperation DN9340E Home page sub-menusTouchstrip Operation on the Home Graphic Equalisation Soft Key FunctionsAutomatic features EQ FlatTouchstrip operation with Graphic equalisation GroupingParametric Equalisation Touchstrip operation with Parametric equalisation EQ removeDynamic Equalisation Lo Threshold / LevelHi Threshold / Level Touchstrip operation with Dynamic equalisation Time constantsFilters Create Filter functionFilter Type Left Encoder Centre Encoder Right Encoder Filter settings Touchstrip operation with FiltersFilter remove Metering Clear Down Sequence To access the Set Up menu pages Setup Menu DN9340ESetup Menu DN9340E GeneralComms channel Remote control via a PCTo switch remote communications off To select a slave remote communications channelTo select a slave communications channel Using a DN9340E for master controlTo select a master remote communications channel To remove the unit from the networkFront Panel lock To set a Panel LockTo remove the Panel Lock Analogue/Digital Input Select To change the input sourceDigital Output Clock Select Presets lockTo set a Presets lock To select the output clock sourceNaming Pages 7 LCD contrast adjustmentDelay options To enter a namePower-up Logo Ethernet Settings Pages 11Ethernet IP Address Ethernet Subnet Mask Setup To check and edit the Subnet MaskUsing the DN9340E Memories To store settingsTo recall settings Addresses Remote ControlConnections Data modelOn a DN9340E Setting the master unit on-lineGetting started On a DN9344ETo set up the names OperationSystem naming To set up the assignment Copy channel functionSolo Tracking operation Overview Helix DN9340E/DN9344E unit interconnectionsConnecting the Helix DN9340/DN9344E units in a daisy chain Ethernet connection wireless option Ethernet ConnectionEthernet connection standard Configuring the DN9340E for Network Communication Configuring the DN9344E for Network CommunicationConnection and Configuration Procedure Serial Connection OptionSerial connection details Press to step through the Set Up pages Controls, Connectors, Indicators DN9344EAlphanumeric displays, SETUP, Metering and Power Power Switch Power on Power on indication Power indicationIndicators, Up and Down Buttons, PC Port and Scribble Strips Indicators1B, 2A and 2B Rear Panel DN9344EMains inlet socket InterfaceSignal Flow DN9344E Signal Flow DN9344EOperation DN9344E Operation DN9344ERemote Comms channels To select a remote communications channel To enable the Contact Closure Relay mode To disable remote communications and relay operationTo change the settings for Inputs 1A and 1B PasswordTo set a password Analogue/Digital Input Select Pages 3To change the settings for Output Digital Output Clock Select Pages 5To change the IP address Ethernet SettingsSubnet Mask To change the Subnet MaskApplication Notes Dynamic EQApplication Notes Application Notes What do we mean by all these Q types? Proportional Q Constant QSymmetrical Q What is AES/EBU? Technical Specification DN9340E 17.1. DN9340EPower Requirements Technical Specification DN9344E 17.2. DN9344ERelay Socket Pin D-type rear Power Pin IEC Service Information BatteryReplacement

Related manuals

Manual 65 pages 57.17 Kb