Klark Teknik Getting started, On a DN9340E, On a DN9344E, Setting the master unit on-line

Page 47

Remote Control

9.4. Getting started

Connect the units using the Ethernet ports as described above. Set the comms address for each slave unit - ignore the master unit for now. It doesn't matter what addresses you use, but each unit MUST have a unique address (two unique addresses for a DN9344E).

On a DN9340E:

1Press and hold HOME (SETUP). The left encoder illuminates, to show that it is active.

2Turn left encoder to select the SLAVE channel number.

3Press HOME (SETUP) to confirm.

On a DN9344E:

1Press SETUP.

2Press and hold SETUP.

3Use the UP and DOWN buttons to select the channel number for Section 1.

4Repeat for Section 2.

5Press SETUP to confirm (unit will display password menu).

6Exit by pressing SETUP to step through the menu.

Setting the master unit on-line:

Once all the slaves have been set up, the master unit can be set on-line. Again, it must have a communication channel allocated, which must not be the same as any of the slaves.

1Press and hold HOME (SETUP). The left encoder illuminates, to show that it is active.

2Turn left encoder to select the channel number for the master unit. Turn the centre encoder to select MASTER mode. Turn the right encoder to select the maximum number of audio channels in the system.

3Press HOME (SETUP) to confirm.

The reason for setting the maximum number of audio channels is to prevent the master unit from wasting time looking for units that are not present and trying to set them on-line, while allowing the user to choose any channel addresses that are convenient. For example, a system including two DN9340Es and two DN9344Es will have 12 audio channels, so set the “Max” value to 12. When the master unit goes on-line it will search for units starting from address 1. Once it finds the correct number of audio channels, it will stop searching.

4The unit will now ask you to choose either to “Set All” slaves to the data contained in the master unit (from the master unit's local copy of the slave data for each address) or to “Get All” data from the slaves themselves. Use the centre encoder to select which one you want.

5Press HOME (SETUP) to confirm. The unit will show a “DETECTING UNITS” page as it searches and initialises the slaves. The system is now on-line.

37

Image 47

Contents DN9340E/DN9344E Page Important Safety Instructions Page Declaration of Conformity Page Contents Setup Menu DN9340E Application Notes Page After Unpacking Safety WarningInstallation Considerations Page DN9340E Front Panel Quick ReferenceDN9344E Front Panel Host Software Versions DN9340E & DN9344E Key FeaturesKey Features Introducing the DN9340E/DN9344EStore and Recall Parameters Remote control operationSpace efficiency Interface to Midas consolesSoft keys display Controls, Connectors, Indicators DN9340EEQ Access and Displays Front Panel DN9340ESoft keys Selected channel both channels if linked. When aBypass, Channel Select, Soft Keys and Alphanumeric Display Touch Strip, Store and Recall, Home Setup and Data Entry PC Port, Metering and Power Word clock Input Rear Panel DN9340EMains Inputs a and BSignal Flow DN9340E Signal Flow DN9340EHome page sub-menus Operation DN9340EOperation DN9340E HomeTouchstrip Operation on the Home Soft Key Functions Graphic EqualisationEQ Flat Automatic featuresGrouping Touchstrip operation with Graphic equalisationParametric Equalisation EQ remove Touchstrip operation with Parametric equalisationHi Threshold / Level Dynamic EqualisationLo Threshold / Level Time constants Touchstrip operation with Dynamic equalisationFilter Type Left Encoder Centre Encoder Right Encoder FiltersCreate Filter function Filter remove Filter settingsTouchstrip operation with Filters Metering Clear Down Sequence General Setup Menu DN9340ESetup Menu DN9340E To access the Set Up menu pagesTo select a slave remote communications channel Remote control via a PCTo switch remote communications off Comms channelTo remove the unit from the network Using a DN9340E for master controlTo select a master remote communications channel To select a slave communications channelTo remove the Panel Lock Front Panel lockTo set a Panel Lock To change the input source Analogue/Digital Input SelectTo select the output clock source Presets lockTo set a Presets lock Digital Output Clock SelectTo enter a name LCD contrast adjustmentDelay options Naming Pages 7Ethernet IP Address Power-up LogoEthernet Settings Pages 11 To check and edit the Subnet Mask Ethernet Subnet Mask SetupTo recall settings Using the DN9340E MemoriesTo store settings Data model Remote ControlConnections AddressesOn a DN9344E Setting the master unit on-lineGetting started On a DN9340ESystem naming To set up the namesOperation Solo Tracking operation To set up the assignmentCopy channel function Helix DN9340E/DN9344E unit interconnections OverviewConnecting the Helix DN9340/DN9344E units in a daisy chain Ethernet connection standard Ethernet connection wireless optionEthernet Connection Configuring the DN9344E for Network Communication Configuring the DN9340E for Network CommunicationSerial connection details Connection and Configuration ProcedureSerial Connection Option Power Switch Power on Power on indication Power indication Controls, Connectors, Indicators DN9344EAlphanumeric displays, SETUP, Metering and Power Press to step through the Set Up pagesIndicators Indicators, Up and Down Buttons, PC Port and Scribble StripsInterface Rear Panel DN9344EMains inlet socket 1B, 2A and 2BSignal Flow DN9344E Signal Flow DN9344ERemote Comms channels Operation DN9344EOperation DN9344E To select a remote communications channel To disable remote communications and relay operation To enable the Contact Closure Relay modeAnalogue/Digital Input Select Pages 3 PasswordTo set a password To change the settings for Inputs 1A and 1BDigital Output Clock Select Pages 5 To change the settings for OutputTo change the Subnet Mask Ethernet SettingsSubnet Mask To change the IP addressDynamic EQ Application NotesApplication Notes Application Notes What do we mean by all these Q types? Constant Q Proportional QSymmetrical Q What is AES/EBU? 17.1. DN9340E Technical Specification DN9340EPower Requirements 17.2. DN9344E Technical Specification DN9344ERelay Socket Pin D-type rear Power Pin IEC Replacement Service InformationBattery

Related manuals

Manual 65 pages 57.17 Kb