Klark Teknik DN9340E, DN9344E specifications Parametric Equalisation, Soft Key Functions

Page 28

Operation: DN9340E

6.3. Parametric Equalisation

Select parametric equalisation by pressing the PARAMETRIC button.

Soft key display

The display for the parametric equaliser is similar to the home page, showing the frequency response

-in this case just for the parametric sections. At the top is a legend that shows which PEQ section is currently active for control and also how many sections are in use. So, for example, if we have four sections in use and we are adjusting the second one, the legend would read “PEQ 2 of 4”. If no PEQ sections are active, then the display is blank except for the ADD key. Press this key to add a section of EQ.

6.3.1Soft Key Functions

selects which PEQ section is to be controlled.

steps through the following pages on the alphanumeric display. After the last page, the next press returns to the first page, and so on.

adds a new PEQ section. There are 12 PEQ sections available to each channel, each of which can be used across the whole frequency range from 20Hz to 20kHz.

pressing this allows an individual section to be switched in and out of circuit without clearing its settings.

Default page displays frequency, Q and level for this section

EQ settings page

•EQ type - this allows control over the characteristics of the equaliser. Proportional, Constant, and Symmetrical curves are available.

•Graph display - three modes are available, to ensure that clear information is available for any application. “Curve” mode shows the overall response of the whole parametric equaliser. “Active” mode shows just the response of the single section currently being selected for adjustment. “Individual” mode shows all the sections, but as individual curves rather than as a single composite response.

18

Image 28

Contents DN9340E/DN9344E Page Important Safety Instructions Page Declaration of Conformity Page Contents Setup Menu DN9340E Application Notes Page Installation Considerations Safety WarningAfter Unpacking Page Quick Reference DN9340E Front PanelDN9344E Front Panel DN9340E & DN9344E Key Features Key FeaturesIntroducing the DN9340E/DN9344E Host Software VersionsRemote control operation Space efficiencyInterface to Midas consoles Store and Recall ParametersControls, Connectors, Indicators DN9340E EQ Access and DisplaysFront Panel DN9340E Soft keys displayBypass, Channel Select, Soft Keys and Alphanumeric Display Selected channel both channels if linked. When aSoft keys Touch Strip, Store and Recall, Home Setup and Data Entry PC Port, Metering and Power Rear Panel DN9340E MainsInputs a and B Word clock InputSignal Flow DN9340E Signal Flow DN9340EOperation DN9340E Operation DN9340EHome Home page sub-menusTouchstrip Operation on the Home Graphic Equalisation Soft Key FunctionsAutomatic features EQ FlatTouchstrip operation with Graphic equalisation GroupingParametric Equalisation Touchstrip operation with Parametric equalisation EQ removeLo Threshold / Level Dynamic EqualisationHi Threshold / Level Touchstrip operation with Dynamic equalisation Time constantsCreate Filter function FiltersFilter Type Left Encoder Centre Encoder Right Encoder Touchstrip operation with Filters Filter settingsFilter remove Metering Clear Down Sequence Setup Menu DN9340E Setup Menu DN9340ETo access the Set Up menu pages GeneralRemote control via a PC To switch remote communications offComms channel To select a slave remote communications channelUsing a DN9340E for master control To select a master remote communications channelTo select a slave communications channel To remove the unit from the networkTo set a Panel Lock Front Panel lockTo remove the Panel Lock Analogue/Digital Input Select To change the input sourcePresets lock To set a Presets lockDigital Output Clock Select To select the output clock sourceLCD contrast adjustment Delay optionsNaming Pages 7 To enter a nameEthernet Settings Pages 11 Power-up LogoEthernet IP Address Ethernet Subnet Mask Setup To check and edit the Subnet MaskTo store settings Using the DN9340E MemoriesTo recall settings Remote Control ConnectionsAddresses Data modelSetting the master unit on-line Getting startedOn a DN9340E On a DN9344EOperation To set up the namesSystem naming Copy channel function To set up the assignmentSolo Tracking operation Overview Helix DN9340E/DN9344E unit interconnectionsConnecting the Helix DN9340/DN9344E units in a daisy chain Ethernet Connection Ethernet connection wireless optionEthernet connection standard Configuring the DN9340E for Network Communication Configuring the DN9344E for Network CommunicationSerial Connection Option Connection and Configuration ProcedureSerial connection details Controls, Connectors, Indicators DN9344E Alphanumeric displays, SETUP, Metering and PowerPress to step through the Set Up pages Power Switch Power on Power on indication Power indicationIndicators, Up and Down Buttons, PC Port and Scribble Strips IndicatorsRear Panel DN9344E Mains inlet socket1B, 2A and 2B InterfaceSignal Flow DN9344E Signal Flow DN9344EOperation DN9344E Operation DN9344ERemote Comms channels To select a remote communications channel To enable the Contact Closure Relay mode To disable remote communications and relay operationPassword To set a passwordTo change the settings for Inputs 1A and 1B Analogue/Digital Input Select Pages 3To change the settings for Output Digital Output Clock Select Pages 5Ethernet Settings Subnet MaskTo change the IP address To change the Subnet MaskApplication Notes Dynamic EQApplication Notes Application Notes What do we mean by all these Q types? Proportional Q Constant QSymmetrical Q What is AES/EBU? Technical Specification DN9340E 17.1. DN9340EPower Requirements Technical Specification DN9344E 17.2. DN9344ERelay Socket Pin D-type rear Power Pin IEC Battery Service InformationReplacement

Related manuals

Manual 65 pages 57.17 Kb