Klark Teknik DN9344E Comms channel, Remote control via a PC, To switch remote communications off

Page 37

Setup Menu: DN9340E

7.2. Comms channel (Page 1)

The Comms page lets you select the communications channel on which the unit, acting as slave, will send/receive data to/from a controlling PC. Alternatively, you can select the DN9340E unit as a master to control the network. The master unit not only controls the network but also acts as a slave unit.

7.2.1Remote control via a PC

Comms channels 1 to 32 are available that provide up to 64 inputs in a slave network comprising DN9340E and/or DN9344E units. The units are remotely controlled from a PC using the Elgar Library Manager and HELIX DN9340E/DN9344E RCS add-in software. For more information on remote control set ups, see Section 10.

Note

When using Ethernet communication, you will need to set up the unit’s IP address and Subnet mask before selecting the comms channel, see Section 7.11 for further details.

To select a slave remote communications channel

1Press HOME (SETUP) for more than one second to access the Set Up menu; you will be taken immediately to the Comms page.

2Use the left control knob to go to the communications channel on which you wish to control the unit remotely, for example, scroll through to channel 14.

3 Press HOME (SETUP) to confirm the selection.

The front panel controls, except the HOME (SETUP) button, are locked out to facilitate remote operation. The display indicates that the unit is under remote control. See Section 10 for further details.

To switch remote communications off

1Press and hold the HOME (SET UP) button to re-open the Comms page.

2Turn the left control knob anti-clockwise to select “Channel” as “Off”.

3Press HOME (SETUP) to confirm the selection.

27

Image 37

Contents DN9340E/DN9344E Page Important Safety Instructions Page Declaration of Conformity Page Contents Setup Menu DN9340E Application Notes Page Installation Considerations Safety WarningAfter Unpacking Page DN9340E Front Panel Quick ReferenceDN9344E Front Panel Key Features DN9340E & DN9344E Key FeaturesIntroducing the DN9340E/DN9344E Host Software VersionsSpace efficiency Remote control operationInterface to Midas consoles Store and Recall ParametersEQ Access and Displays Controls, Connectors, Indicators DN9340EFront Panel DN9340E Soft keys displayBypass, Channel Select, Soft Keys and Alphanumeric Display Selected channel both channels if linked. When aSoft keys Touch Strip, Store and Recall, Home Setup and Data Entry PC Port, Metering and Power Mains Rear Panel DN9340EInputs a and B Word clock InputSignal Flow DN9340E Signal Flow DN9340EOperation DN9340E Operation DN9340EHome Home page sub-menusTouchstrip Operation on the Home Soft Key Functions Graphic EqualisationEQ Flat Automatic featuresGrouping Touchstrip operation with Graphic equalisationParametric Equalisation EQ remove Touchstrip operation with Parametric equalisationLo Threshold / Level Dynamic EqualisationHi Threshold / Level Time constants Touchstrip operation with Dynamic equalisationCreate Filter function FiltersFilter Type Left Encoder Centre Encoder Right Encoder Touchstrip operation with Filters Filter settingsFilter remove Metering Clear Down Sequence Setup Menu DN9340E Setup Menu DN9340ETo access the Set Up menu pages GeneralTo switch remote communications off Remote control via a PCComms channel To select a slave remote communications channelTo select a master remote communications channel Using a DN9340E for master controlTo select a slave communications channel To remove the unit from the networkTo set a Panel Lock Front Panel lockTo remove the Panel Lock To change the input source Analogue/Digital Input SelectTo set a Presets lock Presets lockDigital Output Clock Select To select the output clock sourceDelay options LCD contrast adjustmentNaming Pages 7 To enter a nameEthernet Settings Pages 11 Power-up LogoEthernet IP Address To check and edit the Subnet Mask Ethernet Subnet Mask SetupTo store settings Using the DN9340E MemoriesTo recall settings Connections Remote ControlAddresses Data modelGetting started Setting the master unit on-lineOn a DN9340E On a DN9344EOperation To set up the namesSystem naming Copy channel function To set up the assignmentSolo Tracking operation Helix DN9340E/DN9344E unit interconnections OverviewConnecting the Helix DN9340/DN9344E units in a daisy chain Ethernet Connection Ethernet connection wireless optionEthernet connection standard Configuring the DN9344E for Network Communication Configuring the DN9340E for Network CommunicationSerial Connection Option Connection and Configuration ProcedureSerial connection details Alphanumeric displays, SETUP, Metering and Power Controls, Connectors, Indicators DN9344EPress to step through the Set Up pages Power Switch Power on Power on indication Power indicationIndicators Indicators, Up and Down Buttons, PC Port and Scribble StripsMains inlet socket Rear Panel DN9344E1B, 2A and 2B InterfaceSignal Flow DN9344E Signal Flow DN9344EOperation DN9344E Operation DN9344ERemote Comms channels To select a remote communications channel To disable remote communications and relay operation To enable the Contact Closure Relay modeTo set a password PasswordTo change the settings for Inputs 1A and 1B Analogue/Digital Input Select Pages 3Digital Output Clock Select Pages 5 To change the settings for OutputSubnet Mask Ethernet SettingsTo change the IP address To change the Subnet MaskDynamic EQ Application NotesApplication Notes Application Notes What do we mean by all these Q types? Constant Q Proportional QSymmetrical Q What is AES/EBU? 17.1. DN9340E Technical Specification DN9340EPower Requirements 17.2. DN9344E Technical Specification DN9344ERelay Socket Pin D-type rear Power Pin IEC Battery Service InformationReplacement

Related manuals

Manual 65 pages 57.17 Kb