JVC DR-MV1B manual Free Rate Function, Selection Of The Audio Channel To Be Recorded On a Disc

Filename [DR-MV1SEK_06DVD Operation2.fm]
DR-MV1SEK_00.book Page 44 Thursday, April 15, 2004 3:30 PM	Masterpage:Left+

44 EN OPERATIONS ON DVD DECK

Free Rate Function		NOTES:
		● You can programme this unit to timer-record, regardless of the disc
To record the entire programme, the unit automatically set the
		remaining time. When the disc remaining time is not enough,
appropriate recording mode depending on the combination of the		recording may stop in the middle of a programme. To avoid this, make
total time of the programme to be recorded and either the		sure of the disc remaining time before setting timer-programming.
remaining disc space or the specified recording time (from 60		(Example) If you programmed to timer-record for 60 minutes in SP
minutes to 480 minutes).		mode on a 120-minute disc, the disc remaining time would be 30
8 To record the entire programme within the actual remaining		minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP
		mode, 180 minutes in EP mode, and 240 minutes in FR480 mode.
disc space
		Timer-recording will not complete beyond these remaining times.
Select “FR (JUST)” in a recording mode selection procedure.		● The maximum recording time of FR (JUST) mode is the same as the
( pg. 45, 47)		recording time of FR480 mode. When timer-programming a long
● Note that this function is available only for timer programming		programme in FR (JUST) mode on a disc whose remaining time is
recording.		short, it is recommended checking the disc remaining time in FR480
8 To record the entire programme by specifying the desired		mode to see if the remaining time is enough for the programme.
		● Even if more than one programme are timer-programmed in FR
recording time
		(JUST) mode, only the first one is recorded.
Select “FR60–FR360”, “FR420” or “FR480” in a recording mode
		● In order to ensure that the recording fits on the disc, this feature may
selection procedure. ( pg. 42, 45, 47)
		leave a slight non-recorded section at the end of the disc.
8 To record a 25-min. long daily programme five times just on		● There may be some noise and sound disturbance at the point on the
		disc where the unit switches the mode.
a same disc for example
Perform “VIDEO Plus+® Timer Programming” ( pg. 45)		Receiving Stereo And Bilingual Programmes
procedure. Be sure to set the recording mode to “FR125” and set
Weekly/Daily Rec Function to “MON–FRI” in step 6 to fit the total		Your unit is equipped with a Digital stereo sound decoder (NICAM)
recording time to the whole disc space.		making reception of stereo and bilingual broadcasts possible.
	A: 1st	When the channel is changed, the type of broadcast being
Blank	B: 2nd	received will be displayed on the TV screen for a few seconds.
	C: 3rd
	D: 4th	Type of Broadcast Being	On-screen Display
	E: 5th
		Received

Regular Monaural NICAM Stereo

NICAM Bilingual

When the same programme is recorded in SP mode instead of in NICAM Monaural “FR125”, the 5th programme cannot be recorded.

Blank

A:1st

B:2nd

C:3rd

D:4th

E:Blank (20 min.)

NOTES:

●“SUPERIMPOSE” must be set to “AUTO”. Otherwise the on-screen displays will not appear. ( pg. 81)

●If the quality of stereo sound being received is poor, the broadcast might be received in monaural with better quality.

Selection Of The Audio Channel To Be Recorded On A Disc

When a programme is recorded on a DVD-RAM or DVD-RW disc in VR mode, all audio channels of the receiving programme are recorded on the disc. When you record a programme on a DVD-R or DVD-RW disc in video mode, select the desired audio channel (from among “NICAM 1/MAIN”, “NICAM 2/SUB”, “MONO”) to be recorded on the disc. ( pg. 81)

NOTE:

Before playing back a programme recorded in stereo, or a bilingual programme, refer to “Audio Channel Selection” on page 30.

Page 44

April 15, 2004 3:30 pm