JVC DR-MV1B manual Scan Mode Set, Tray Lock DVD Deck Only, To lock tray, To unlock tray

Page 89

Filename [DR-MV1SEK_10Subsidiary.fm]

 

DR-MV1SEK_10Subsidiary.fm Page 89 Thursday, April 22, 2004 6:38 PM

Masterpage:Right+

 

SUBSIDIARY SETTINGS EN 89

Scan Mode Set

If you connect the unit and TV with Component Video Connection ( pg. 18), you can select the scan mode from two modes: Interlaced scan mode which is used in the conventional TV system, and Progressive scan mode which enables reproduction of higher-quality images. For details, refer to “GLOSSARY”

( pg. 95).

ATTENTION:

Your TV needs to be compatible with PAL Progressive.

●Turn on the unit.

●Turn on the TV and select the AV mode.

●Slide the TV/CABLE/SAT/DVD switch to DVD.

VCR/DVD

SAT

1 2 3

4 5 6

7 8 9

0

PROGRESSIVE SCAN

1 Press VCR/DVD repeatedly so that the DVD lamp lights up on the unit.

2 Press PROGRESSIVE SCAN for 3 or more seconds.

●Video output indicator () lights on the front display panel if Progressive scan mode has been established. ( pg. 14)

●Each press of PROGRESSIVE SCAN for 3 or more seconds switches the scan mode.

NOTES:

●When the progressive mode is set, be sure to set “L-1 OUTPUT” to “COMPONENT”. ( pg. 74) Progressive scan is output only from COMPONENT VIDEO OUT connector.

●Interlaced scan mode is the setting at your purchase.

●Interlaced scan mode might be suitable depending on video material.

●Scan mode cannot be set while menu screen is displayed.

●When the Progressive scan mode is engaged, no video signal is output from S-VIDEO OUT connector and L-1 IN/OUT connector.

Watch the image on VCR deck in the Progressive scan mode via component video

ASet the Progressive-compatible TV to the component input mode.

B Press VCR/DVD repeatedly so that the DVD lamp lights up on the unit, then press PROGRESSIVE SCAN for 3 or more

seconds so that the Video output indicator () lights on the front display panel.

C Press VCR/DVD repeatedly so that the VCR lamp lights up on the unit.

D Press VCR].

● “VCR]” lights up on the unit. E Insert a cassette and press 4.

NOTES:

●Be sure to engage the DVD deck in stop mode.

●It is not possible to perform the above steps when the DVD deck is in timer standby mode.

●If the image and sound is distorted, press VCR/DVD repeatedly.

Tray Lock (DVD Deck Only)

You can lock the disc tray to prohibit the unwanted disc ejection by children.

●Turn off the unit when the DVD deck is selected.

x 8

To lock tray

While the unit is turned off, press and hold 8, then press x on the unit. “LOCKED” appears on the front display panel and the disc tray is locked.

To unlock tray

While the unit is turned off, press and hold 8, then press x on the unit. “UNLOCK” appears on the front display panel.

Page 89

April 22, 2004 6:32 pm

Page 88 Page 90
Image 89
Page 88 Page 90
Contents DR-MV1S DR-MV1B Mains outlet Filename DR-MV1SEK02Safety.fmApril 15, 2004 1127 am MasterpageLeft0Do not place the unit MasterpageRight+Do not block the unit’s ventilation openings or holes To mobile phone usersMasterpageLeft+ Some Do’s And Don’ts On The Safe Use Of EquipmentAbove ALL Engage the VCR deck’s timer mode.  pg Engage the DVD deck’s timer mode.  pgWatch another programme while recording on the unit Operate the VCR deck while recording on the DVD deckContents Recordable/playable Discs About DiscsDVD-RAM DVD-RW DVD-RUnplayable Discs Discs For Playback OnlyRegion Number DVD-RAM Recording Medium And FormatFile Structure Of Discs DVD Video Marks Care And Handling Of Discs Maintenance of discsLabel side Recording sideApril 15, 2004 319 pm Front ViewFilename DR-MV1SEK04Name.fm Rear View C D EF GFront Display Panel On-Screen Display VCR deck On-Screen Display DVD deckHow To Use Remote ControlCheck Contents When your TV’s Scart To connect to a TV with AV input connectorsConnector accepts Basic ConnectionNumber Set Auto Set UpAuto Channel Set/Auto Clock Set/Auto Guide Program Before starting, make sure of the followingCable  pg , the unit will automatically perform Preset Preset DownloadDownload instead of the Auto Set Up in on page 19. After Set/Auto Guide Program Number SetLink Functions DVD Deck Only Results Of Auto Set Up/Preset Download AppearingOn The Front Display Panel Enter On-screen Language SetMenu/Audio/Subtitle Language Set DVD deck only Installing Satellite Controller Satellite Receiver Control Setting DVDSetting Satellite Receiver’s Brand And Channel Deck OnlyBrand Name Code Pan&Scan/Letter Box Monitor Set DVD Deck OnlyPan&Scan Letter BoxBasic Playback High-Speed Search Playback FeaturesStill Picture/Frame-By-Frame Playback Resume FunctionSlow Motion Skip SearchAngle Selection Stop modeChecking The Time Information Subtitle SelectionAudio Channel Selection Audio Language/Sound SelectionPlayback Control PBC Function Press Audio or w e to selectTo Watch a Programme Previously Recorded While Recording Live Memory PlaybackRecording/playback Status Display Pressing 2 or 6 allows you to locate the desired scenesRecording screen Overview Of Live Memory PlaybackDisplay During Live Memory Playback Buttons To Be Used During Live Memory Playback How To Access The On-screen Bar Using The On-screen BarContents of the on-screen bar during playback Basic Operation On The On-screen BarDuring playback Repeat PlaybackDVD-RAM/RW/R Audio CD/Video CD/SVCD/JPEG/MP3Time Search Press Enter to clear 3D-ON from the screen Adjusting The Picture QualitySimulated Surround Effect While stopped Setting The Progressive Mode Programme PlaybackPerform steps 1 Select The Switching Interval Of The Slide ShowRandom Playback Parental Lock To Change The SettingsTo Temporarily Release Parental Lock To Set Parental Lock For The First TimeRecording Resume Function Recording ModeBasic Recording Instant Timer Recording ITR Recording FeaturesSlide the TV/CABLE/SAT/DVD switch to TV Watch Another Programme While Recording On The UnitSelection Of The Audio Channel To Be Recorded On a Disc Free Rate FunctionDisc space Recording timeVideo Plus+ Timer ProgrammingDaily/Weekly Recording Satellite Receiver UsersPDC Recording Manual Timer ProgrammingPress PROG/CHECK to access the Programme Check screen Disc On-Disc Timer ProgrammingTo Timer-record The Programme With The Programmed How Discs Are Overwritten Check, Cancel And Change Programmes When Programmes Overlap Each OtherCancel To cancel the programmeAbout the Automatic Satellite Programme Recording Indicator on the front display panelCompact VHS Usable cassettes Full-Size VHSIndex Search Playback Features High-Speed SearchQuick Rewind a Little Manual Tracking Next Function MemorySoundtrack Selection VHS Progressive ScanLoad a cassette with the record safety tab intact Basic Recording Recording FeaturesAccidental erasure prevention VCR recording lamp lights off on the unitTo Record Nicam Stereo and Bilingual Programmes S.T. Picture SystemPlayback RecordingPress VCR Timer # to engage the unit’s timer mode. You can use the remote control to enter the PlusCode numberVCR timer lamp lights up on the unit and the DVD deck is Panel. Press Cancel & and input a valid PlusCode numberApril 22, 2004 509 pm OffRefer to steps 7 11 in Manual Timer Programming  pg To cancel a programme Press Cancel & to cancel a programmePress VCR Timer # About registration of information Library Database DVD NaviAbout editing of programmes Limitations of registrationPress 8 to cancel pause mode after pressing Navigation When you want the pluralScan For Beginnings Of Programmes Modify IndexModify Category Modify Programme NameDelete Programme Protect TitleDelete Unwanted Part Of The Programme Modify Play List InformationCreate Play List To modify the pointsAdd Scenes To a Play List Move ScenesDelete Play List Delete Unwanted Part From Play ListPlay Back Play List Scan For Programme From Library Modify Library InformationRegister Disc Delete InformationFor MP3 Playback Locating The Desired Group And TracksFor Jpeg Playback On completion of the playback of all the itemsFor VCR deck Dubbing An Entire CassetteFor DVD deck Record Pause mode Locate the point from where you want to start dubbing, thenPrepare the VCR deck for dubbing Press VCR/DVD repeatedly so that the VCR lamp lights up onLoad a disc you want to dub Dubbing An Entire DiscPress DVD to select the dubbing direction Press and hold DUB for more than 2 seconds to start73 DUB Dubbing a Part Of a DiscMasterpageLeft+ Press and hold 9, then press 7 so that the VCR deck entersDV Dubbing DVD Deck Only Performing dubbing without using the DV Dubbing controllerEdit From a Camcorder When using your unit as the source player Select Setting Output And L-1 Input SettingRegular video signals, set to Video Compatible with the Y/C signalExample Dubbing to an MD Input SettingDigital Audio Dubbing TV Multi-Brand Remote Control Remote Control FunctionsRemote control 1/2/3/4 Code Switching 3 or 4. The remote control is preset to send 3 code signals65, 67, 74, 86 Satellite Receiver Multi-Brand Remote ControlSlide the TV/CABLE/SAT/DVD switch to CABLE/SAT Simple Connections Connecting To a Satellite ReceiverProgramme When you can’t switch the audio channel of a bilingualFilename DR-MV1SEK10Subsidiary.fm Mode Set DVD DeckUtility  pg Others  pgThis function works only for the Nicam bilingual programme During Power Save modePower Save does not work when According to your preference. Normally select Auto Auto Picture quality is adjusted automaticallyContaining a lot of noise Lots of flat, same-coloured surfaces such as cartoonsTuner Set Video Plus+ System SetupGuide Program Number Set Auto Channel SetManual Channel Set Press SET UP to close the Confirmation screenView the Confirmation screen. Scan Completed is Repeat steps 4 9 as necessaryDelete a Channel Fine-Tuning Channels Already StoredChange Station Channel Position Set Stations aScreen the default setting is OFF PDC signalClock Set Just Clock function provides accurate time keeping throughFormat a Disc DVD Deck Only To be chosen when you want to record, erase, orFormat a DVD-RAM Disc Format a DVD-RW DiscAfter finalising For DVD-R/RW Video mode discs Cancel The Finalisation Of a DVD-RW DiscFinalise a Disc DVD Deck Only Finalise a DVD-R/RW DiscTray Lock DVD Deck Only Scan Mode SetTo lock tray To unlock trayGeneral Playback DVD DeckPlayback VCR Deck TV is not set to the AV mode. Set the TV to the AV modeRecording VCR Deck Recording DVD DeckPower failure occurred Set date and time correctly.  pg Timer Recording DVD DeckTimer Recording VCR Deck Initialising DVD Deck Only Other ProblemsOn-screen Message DVD Deck Only For RF/AV/S-VIDEO connectionDuring Live Memory playback, 8 has been pressed.  pg Timer recording has finished during Live Memory playbackAn invalid PlusCode number has been input.  pg Refers to individual chapters included in a title Glossary ENPower consumption Power requirementTemperature Dimensions WxHxDLanguage Code List Country/Area Code List for Parental Lock DR-MV1SEK00.book Page 99 Thursday, April 15, 2004 330 PM Station Name TV Station And ID ListTV Station Channel Number Guide Setting The Progressive Mode Recording Mode Recording Resume Function26 41, 51 Delete ProgrammeMasterpageRight0 Memo EN104April 23, 2004 1015 am Filename DR-MV1SEK12Cov4.fm
Top Page Image Contents