JVC DR-MV1B manual On-Disc Timer Programming, To Timer-record The Programme With The Programmed

Filename [DR-MV1SEK_06DVD Operation2.fm]
DR-MV1SEK_00.book Page 47 Thursday, April 15, 2004 3:30 PM	Masterpage:Right+
	OPERATIONS ON DVD DECK EN 47
On-Disc Timer Programming	8 Press w e to select “TV PROG”, then press rt to select the
	desired channel.
	9 Set “DAILY/WEEKLY” option.
	● Refer to step 6 in “VIDEO Plus+® Timer Programming” ( pg. 45).
	● It is necessary to set “DAILY/WEEKLY” option for On-Disc Timer
	Programming. ( pg. 45, “Daily/Weekly Recording”)

On-Disc Timer Programming is a function used with discs that are	10 Set the other recording options as required.
especially intended for a specific programme. The disc is then	● You can select XP, SP, LP, EP or FR480 mode for “REC MODE”.
	However, you cannot select FR (JUST), FR60–FR360 and FR420.
programmed for a programme you always watch every day or
	● Refer to step 6 in “VIDEO Plus+® Timer Programming” ( pg. 45).
every week. Since older programmes are automatically	● It is not possible to use the Free Rate function. ( pg. 44)
overwritten, a single DVD-RAM/RW (VR mode) disc can be used
	11 Press ENTER to access the Programme Confirmation screen.
without worrying about how much recording capacity remains.
( pg. 48)	12 Press ENTER to complete timer programming.
You can programme each disc to timer-record as many as	● To programme another timer, repeat steps 3 – 12.
8 programmes.
	Satellite Receiver Users
● Make sure that the unit’s built-in clock is set properly.	To timer-record a satellite broadcast using the On-Disc Timer
● Turn on the unit.	Programming function:
● Turn on the TV and select the AV mode.	A Perform “Satellite Receiver Control Setting (DVD Deck Only)”
● Slide the TV/CABLE/SAT/DVD switch to DVD.	( pg. 23).
	B Perform “On-Disc Timer Programming” ( pg. 47). In
ATTENTION:	step 10, you cannot set “VPS/PDC” to “ON”.
● On-Disc Timer Programming is possible only with the disc for On-	C Leave the satellite receiver’s power on.
Disc Timer Programming.	To Timer-record The Programme With The Programmed
● If data is recorded on a disc for On-Disc Timer Programming using
a unit from another manufacturer, On-Disc Timer Programming	Disc
may no longer function properly.

DVD TIMER (#)			SAT
VCR/DVD			1
1	2	3
4	5	6
7	8	9
PROG/CHECK	0

ENTER rtw e

To Make The Disc For On-Disc Timer Programming

1 Load a recordable disc.

2 Press VCR/DVD repeatedly so that the DVD lamp lights up on the unit.

3 Press PROG/CHECK to access the Programme Check screen.

4 When On-Disc Timer Programming is made for the first time on the disc

Press rt to select “DISC TIMER PRGM”, then press ENTER.

●When some programmes are recorded on the disc, a caution message appears. In such a case, backup the programmes as required, then format the disc before making On-Disc Timer Programming. ( pg. 87)

When On-Disc Timer Programming has already been made on the disc

Press rt to select “NEW TIMER PROGRAMME”, then press

ENTER.

5 Press rt to set the desired date.

●The current date appears on the TV screen. The date you enter appears in its place.

1 Load a programmed disc.

2 Press DVD TIMER (#). The unit turns off and “” appears on the front display panel. The DVD timer lamp also lights up on the unit and the VCR deck is automatically selected. Press 1 to turn off the unit. When the VCR deck is in timer standby mode, the unit is automatically turned off.

●To disengage the timer mode, press 1 again.

NOTES:

●Even if On-Disc Timer Programming is overlapping with other timer programming, any caution message does not appear. In such a case, recording will be executed in the descending order of the recording start time of the programme.

●On-Disc Timer Programming is not possible on a DVD-RW disc formatted in video mode. ( pg. 87)

●The information of a programme recorded with On-Disc Timer Programming is not stored in the library. ( pg. 65)

●The play list is not created for the programmes recorded with On-Disc Timer Programming. ( pg. 62)

●VIDEO Plus+ Timer Programming is not possible on the discs used exclusively for On-Disc Timer Programming.

●Manual Timer Programming is not possible on the On-Disc Timer Programmed disc. ( pg. 46)

●Basic Recording is not possible on the On-Disc Timer Programmed disc. ( pg. 42)

●The On-Disc Timer Programming function does not work on the unit form other manufactures even if the On-Disc Timer Programmed disc is loaded.

●The beginning of a programme may not be recorded. Also, if the 1st programme’s recording stop time and the 2nd programme’s recording start time is the same, the ending of the 1st programme may not be recorded.

●If there is a power cut while recording, the recordings before the power cut are not guaranteed.

6 Press w e to select “START”, then press rt to set the desired start time.

●Each press of rt advances/goes back the start time in 1-min. increments.

●To advance/go back the start time in 30-min. increments, press and hold rt.

7 Press w e to select “STOP”, then press rt to set the desired stop time.

●Each press of rt advances/goes back the stop time in 1-min. increments.

●To advance/go back the stop time in 30-min. increments, press and hold rt.

Page 47

April 15, 2004 3:30 pm