JVC DR-MV1B Timer Programming, Video Plus+, Daily/Weekly Recording, Satellite Receiver Users

Filename [DR-MV1SEK_06DVD Operation2.fm]
DR-MV1SEK_00.book Page 45 Thursday, April 15, 2004 3:30 PM			Masterpage:Right+
			OPERATIONS ON DVD DECK EN 45
VIDEO Plus+	®	Timer Programming	6 Press w e to select the desired recording option as required.
			Press rt to select the desired setting, then press ENTER.
			● “STOP” (To advance/go back the stop time by 30 minutes, press and
			hold rt).
			● “DAILY/WEEKLY” ( pg. 45, “Daily/Weekly Recording”)
			● “REC MODE” ( pg. 42, “Recording Mode”)
You can programme this unit to timer-record as many as			● “NAME” ( pg. 61, “Modify Programme Name”)
			● “VPS/PDC” ( pg. 57, “PDC Recording”)*
8 programmes.			* VPS (Video Programme System) recording is not currently available
With the VIDEO Plus+ system, timer programming is greatly
			in the U.K. and not possible with this unit.
simplified because each TV programme has a corresponding code
			7 Press ENTER to access the Programme Confirmation screen.
number which your unit is able to recognise.
You can use the remote control to enter the PlusCode number.			8 Press ENTER to complete timer programming.

● Make sure that the unit’s built-in clock is set properly.				● To programme another timer, repeat steps 3 – 8.
				● If “PROGRAM OVERLAPPED” appears on the TV screen, see
● Turn on the unit.				page 49.
● Turn on the TV and select the AV mode.				9 Press DVD TIMER (#) to engage the unit’s timer mode. The
● Slide the TV/CABLE/SAT/DVD switch to DVD.
				DVD timer lamp lights up on the unit and the VCR deck is
				automatically selected. Press 1 to turn off the unit. When the
				VCR deck is in timer standby mode, the unit is automatically turned
#			SAT	off.
DVD TIMER ( )				● To disengage the timer mode, press DVD TIMER (#) again.
VCR/DVD
	2	3
1				NOTES:
4	5	6	0 – 9
7	8	9		● There may be cases that VIDEO Plus+ Timer Programming function
CANCEL (X)	0			prolongs the stop time of the programming.
VIDEO Plus+				● When two successive programmes are recorded on a DVD-RW disc
ENTER				with VIDEO Plus+ Timer Programming function, the beginning of the
			RETURN	second one may be left off the recording.
				● VIDEO Plus+ Timer Programming is not possible on the discs used
				exclusively for On-Disc Timer Programming.
CLEAR (8)				● If the copy limited programme is received during timer-recording, the
				unit enters Record Pause mode. Recording starts again if it is
				switched to a recordable broadcast during the time you programmed.
				IMPORTANT:
				If you have moved to a different area or if a broadcasting station’s
				programme number has been changed, the wrong programme
				number will be displayed on the VIDEO Plus+ programme screen in
1 Load a recordable disc.				step 5. When this happens, set the correct Guide Program number
				for that station. ( pg. 83, “VIDEO Plus+® System Setup”)
2 Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.				Satellite Receiver Users
3 Press VIDEO Plus+ to access the VIDEO Plus+ screen.
				To timer-record a satellite broadcast using the VIDEO Plus+
4 Press the number keys to				system:
enter the PlusCode number of a				A Perform “Satellite Receiver Control Setting (DVD Deck Only)”
programme you wish to record,				( pg. 23).
then press ENTER.				B Perform “VIDEO Plus+® Timer Programming” ( pg. 45).
● If you have made a mistake, press				C Leave the satellite receiver’s power on.
CANCEL (&) and input the correct				Daily/Weekly Recording
number before you press ENTER.
● To clear all entered numbers at a
time, press CLEAR(8).				You can record programmes with one of the following weekly/daily
● If the number you entered is invalid, “PlusCode NO. ERROR				timer settings.
CONFIRM PlusCode NO. THEN RETRY” appears on the TV screen.				WEEKLY: Select to record a weekly programme.
Input a valid PlusCode number.
				MON–FRI: Select to record a daily programme from Monday
● If “GUIDE PROGRAMME IS NOT SET SELECT CHANNEL YOU
WANT TO RECORD” appears on the TV screen, set Guide Program				through Friday.
numbers manually. ( pg. 83)				MON–SAT: Select to record a daily programme from Monday
● When “PROGRAMME FULL DELETE UNWANTED TIMER				through Saturday.
PROGRAMME” appears on the TV screen, you need to cancel some				SUN–SAT: Select to record a daily programme from Sunday
of the reserved programmes. ( pg. 49)				through Saturday.

5 The PlusCode number you entered and the matching timer- recording information are displayed on the TV screen. Check the programme data.

●To cancel this setting, press VIDEO Plus+ or RETURN.

IMPORTANT:

Make sure the channel position number you wish to record is displayed; if not, see “VIDEO Plus+® System Setup” ( pg. 83) and set the Guide Program number correctly.

Page 45

April 15, 2004 3:30 pm