JVC DR-MV1B manual Timer Recording DVD Deck, Timer Recording VCR Deck

Filename [DR-MV1SEK_10Subsidiary.fm]
DR-MV1SEK_00.book Page 92 Thursday, April 15, 2004 3:30 PM	Masterpage:Left+

92 EN TROUBLESHOOTING

Timer Recording (DVD Deck)

Timer programming cannot be made.

●Date and time is not correct.

]Set date and time correctly. ( pg. 86)

●The timer is not engaged.

]Press DVD TIMER (#) and confirm that the DVD timer lamp lights up on the unit.

●Timer recording is in progress.

]Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.

Timer programming recording does not start.

●Date and time is not correct.

]Set date and time correctly. ( pg. 86)

●The timer is not engaged.

]Press DVD TIMER (#) and confirm that the DVD timer lamp lights up on the unit.

●There is a power outage while the DVD deck is in the timer standby mode.

]The unit does not enter timer standby mode automatically when the power is restored to the unit. Engage the timer standby mode again.

VIDEO Plus+ Timer Programming cannot be made.

●Date and time set on the unit is not correct. ]Set date and time correctly. ( pg. 86)

●The channel position does not correspond to that in the receiving area.

]Set the correct channel position for the receiving broadcast. ( pg. 83)

Automatic Satellite Programme Recording does not start.

●The satellite receiver is not connected properly to this unit. ]Connect the satellite receiver to the L-2 IN/DECODER

connector properly. ( pg. 50)

On the front display panel, “– –:– –” appears.

●Power failure occurred.

]Set date and time correctly. ( pg. 86)

“PROGRAM FULL” appears on the TV screen during timer programming.

●Eight programmes have already been timer programmed. ]Clear unnecessary programmes on the unit, then try timer

programming again. ( pg. 49)

The disc space does not increase when recorded programmes are cleared.

●The PC’s data recorded on a DVD-RAM drive cannot be cleared on this unit.

]Format the disc. (When the disc is soiled, wipe the disc with a soft dry cloth before formatting.) ( pg. 11, 87)

Timer Recording (VCR Deck)

Timer programming cannot be made.

●Date and time is not correct.

]Set date and time correctly. ( pg. 86)

●The timer is not engaged.

]Press VCR TIMER (#) and confirm that the VCR timer lamp lights up on the unit.

●Timer recording is in progress.

]Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.

Timer programming recording does not start.

●Date and time is not correct.

]Set date and time correctly. ( pg. 86)

●The timer is not engaged.

]Press VCR TIMER (#) and confirm that the VCR timer lamp lights up on the unit.

The VCR Timer lamp on the unit won’t stop blinking.

●The timer is engaged but there’s no cassette loaded. ]Load a cassette with the record safety tab intact.

●The loaded cassette has had its record safety tab removed. ]Remove the cassette and cover the hole with adhesive tape, or

insert a cassette with the record safety tab intact.

The tape is automatically ejected, then the unit is shut off.

●The end of the tape was reached during timer recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

●The end of the tape was reached during Instant Timer Recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

VIDEO Plus+ Timer Programming cannot be made.

●Date and time set on the unit is not correct. ]Set date and time correctly. ( pg. 86)

●The channel position does not correspond to that in the

receiving area.

]Set the correct channel position for the receiving broadcast. ( pg. 84)

The VIDEO Plus+ system does not timer-record properly.

●The unit’s channel positions have been set incorrectly. ]Refer to “VIDEO Plus+® System Setup” ( pg. 83) and re-

perform the procedure.

Page 92

April 15, 2004 3:21 pm