JVC DR-MV1B DV Dubbing DVD Deck Only, Performing dubbing without using the DV Dubbing controller

Filename [DR-MV1SEK_09Editing.fm]
DR-MV1SEK_00.book Page 71 Thursday, April 15, 2004 3:30 PM	Masterpage:Right+

EDITING EN 71

	DV Dubbing (DVD Deck Only)	1 Connect a camcorder or DV equipment to the DV IN connector
		on the unit’s front panel.
		2 Load a DVD-RAM/RW/R disc on the unit.
You can dub programmes from a camcorder or DV equipment
		3 Press PR +/– to set the channel to “DV DUBBING”.
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV		● The “DV DUBBING” controller appears on the TV screen.
equipment functions during dubbing.		● If “	” does not appear on the “DV DUBBING” controller, make
		sure the DV equipment is connected correctly.
		4 Press w e to select		, then press ENTER.
NOTE:
When you connect a PC to the DV IN connector, we do not assure		5 Press rt to select the desired
the normal operation of this unit.		sound track, then press ENTER.
		AUDIO 1: Select this to record the
	Your unit	original stereo sound played
		back on the connected DV

STANDBY/ON equipment.

VCR/DVD VCR DVD VCR DUB DVD

AUDIO 2: Select this to record the

		VPS/PDC VCD
DVD	F-1	DV HS

	HDD DVD	+
		BS
S-VIDEO	VIDEO (MONO) L - AUDIO - R
Camcorder
DV equipment

REMAIN		PR	SAT	DV IN
REC MODE	<< SLOW >>		DVD

DV IN connector

DV cable (VC-VDV 204U)

(not provided)

DV connector

dubbed stereo sound played back on the connected DV equipment.

MIX: Select this to record the sound of both “AUDIO 1” and “AUDIO 2”.

●Note that this selection is not available when the source programme is recorded in 16BIT (48 kHz) mode.

6 Press REC MODE repeatedly to set the recording mode.

7 Locate the point from where you want to start dubbing, then stop or pause playback by pressing the following buttons on the remote control: 4, 5, 3, 8, 9

●To play back in slow speed (1/10 of the normal speed), press 9 to pause playback, then press 3 or 5.

●To play back frame-by-frame, press 9 to pause playback, then press 9 repeatedly. Each press of 9 advances a frame.

●To change the playback direction, press 3 or 5.

8 Press w e to select , then press ENTER. The dubbing starts.

●Playback on the external DV equipment and recording on the unit should start simultaneously.

●When the playback from the beginning is not possible, the “DV DUBBING” controller cannot be used. Perform dubbing without using the “DV DUBBING” controller. ( below)

●To pause dubbing, press w e to select , then press ENTER. Both the unit and the external DV equipment pause dubbing. Pressing 9 on the unit also works the same way.

●To clear the “DV DUBBING” controller from the TV screen, press ON SCREEN.

9 Press 8 on the remote control to stop dubbing.

●Both the unit and the external DV equipment stop dubbing.

NOTES:

●Dubbing copyright guarded programmes is not possible.

●Original DV informations such as the recording date and time are not recorded.

●The superimposed indication during the operation or dubbing is not recorded.

●It is not possible to perform dubbing when “VCR]” lights up on the unit. Press VCR] so that “VCR]” lights off.

Performing dubbing without using the “DV DUBBING” controller

APress PR +/– to set the channel to “DV DUBBING”.

BPress REC MODE repeatedly to set the recording mode.

CStart playback on the external DV equipment slightly before the actual point from where you wish to start dubbing.

D Press 7 on the unit to start recording. Or press and hold 7 and press 4 on the remote control. The dubbing starts.

E When the dubbing ends, press 8 on the unit, then stop playback on the external DV equipment.

Page 71

April 15, 2004 3:18 pm