Installer Menu (Cont.)
016 - EN TIMER (Enable On/Off Timers) *
If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off Timers.
Note: Clock must be set in order to use timers.
017 - ALARM *
Gives the installer the option of making the Alarm function avail- able to the end user. If set to 1, the Alarm function is available to the end user. Set to 0 to disable the Alarm function.
Note: Clock must be set before the Alarm function will work.
021 - V-CHIP (Parental Control) *
Set to 1 to activate
022 - MAX BLK HRS (Maximum Block Hours) *
Sets hours from 0 to 99 for the maximum
023 - CAPTION LOCK
If set to 0, captions are OFF when the STB is turned ON. Set to 1 to use the caption setting configured before the STB was turned OFF when the STB is turned ON.
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channels with either Channel Up/ Down or by direct keypad entry. If set to 0, only those channels that are active in the STB’s memory can be selected.
029 - OLD OCV (On Command Video™)
Set to 1 for operation with systems from On Command Corporation.
030 - ACK MASK
MPI Communication Parameter. Leave at default setting unless changed by
031 - POLL RATE
MPI Communication Parameter. Selects Poll Rate for MPI. Leave at default setting unless changed by
032 - TIMING PULSE
MPI Communication Parameter. Leave at default setting unless changed by
034 - CAMPORT EN. (Camera Port Enable)
Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional.
* Only affects Function Menu if enabled by some PPV providers.
035 - COMPPORT EN. (Computer Port Enable)
Enable/disable STB HDMI 1 input jack. Set to 0 to disable HDMI1. Set to 1 to enable HDMI1.
Note: This setting is ignored if item 093 RJP AVAILABLE is set to 1.
038 - YPrPb EN. (Rear Component Video Enable)
Set to 1 to enable display panel rear Component Video input jacks. Set to 0 to disable display panel rear Component Video input jacks.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0 to disable display panel rear Aux (Video 1) input.
040 - AUTO CAMPORT
Set to 1 to automatically switch to Camport when equipment is connected to Video input on the STB rear panel. Set to 0 to dis- able STB rear panel Video automatic source selection.
Note: If set to 1, item 093 RJP AVAILABLE is automatically set to 0 and item 046 STRT AUX SRCE cannot be set to 2.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting Aux source. When turned ON, the STB will tune to starting Aux source if item 004 STRT CHANNEL is set to 0.
If item 093 RJP AVAILABLE is set to 0 and item 040 AUTO
CAMPORT is set to 0: |
| |||
1 | = Video 1 | 4 | = RGB | 255 = Last Aux |
2 | = Video 2 | 5 | = HDMI 2 |
|
3 | = HDMI 1 | 6 | = Component |
|
If item 093 RJP AVAILABLE is set to 1: | ||||
2 | = Video 2 | 5 | = HDMI 2 | 6 = Component |
If item 040 AUTO CAMPORT is set to 1: | ||||
1 | = Video 1 | 5 | = HDMI 2 |
|
3 | = HDMI 1 | 6 | = Component |
|
4 | = RGB |
|
|
|
047 - AUX STATUS
Set to 1 for MPI Aux source to be reported as a channel number instead of channel 0. Set to 0 to disable Aux identification change. Controls MPI status channel response for Aux inputs.
053 - DIS. CH-TIME (Disable Channel-Time)
Set to 1 to disable the
069 - EN.
46 |