Avaya S8710 Single control network, Duplicated control network, Setting selected traps alarming

Page 30

Configuring the SNMP modules in the UPS

8Connect one end of a CAT5 cable to the RJ45 connector on the UPS 1 SNMP module and the other end to the next available port on the Ethernet switch for Control Network A (CNA).

9Depending on whether a single or duplicated control network is installed (Single control network on page 30 or Duplicated control network on page 30), repeat steps 5 thru 7 for the UPS 2 SNMP module.

10Connect one end of a CAT5 cable to the RJ45 connector on the UPS 2 SNMP module and the other end to the next available port on the Ethernet switch for Control Network A (CNA).

Single control network

If a single control network, use the following address and cable connection information for UPS 2:

•UPS IP address / Subnet mask = 198.152.255.238 / 255.255.255.0

•Default Gateway IP address = 198.152.254.202

•Host Table trap receiver IP address = 198.152.254.202

•Local network administrator supplied information as required for Get and Set community name strings.

•Cable the RJ45 connector on the UPS 2 SNMP module to the next available port on the Ethernet switch for Control Network A (CNA).

Duplicated control network

If a duplicated control network, use the following addresses and cable connection information for UPS 2:

•UPS IPaddress / Subnet mask = 198.152.255.239 / 255.255.255.0

•Default Gateway IP address = 198.152.255.202

•Host Table trap receiver IP address = 198.152.255.202

•Local network administrator supplied information as required for Get and Set community name strings.

•Cable the RJ45 connector on the UPS 2 SNMP module to the next available port on the Ethernet switch for Control Network B (CNB).

Setting selected traps (alarming)

The default is to set all traps, which may result in large log entries. Therefore, only set the following traps. See the User’s Guide that comes with the SNMP module for the menus and commands for setting these traps.

•UPS on Battery—Indicates AC fail with pending shutdown based on battery reserve available

•UPS in Bypass—Failure either Failed UPS or overload

•Replace battery—Failure of periodic (28-day) battery test indicating battery needs to be replaced.

30

Installing and Configuring the Avaya S8700 or S8710 Media Server

 

June 2004

Page 29 Page 31
Image 30
Page 29 Page 31
Contents 6HUYHU Copyright 2004, Avaya Inc All Rights Reserved SOC/REN Installation and Repairs Contents Configuring the hardware in the rack Connecting to the IPSIs Accessing the media server Using this documentation About This DocumentationAudience General Physical dimensionsConventions TerminologyCommands Downloading this book and updates from the Web Downloading this documentationSafety labels and security alert labels Related resourcesSending us comments Technical assistanceTrademarks Within the USIntroduction Pre-installation information Before you go on siteDownloading license and Avaya authentication files Equipment specifications Before you start the installationEquipment specifications Required hardware Documentation Connecting to the customer’s network Figure notes Connecting the USB modems Connecting to collocated serversConnecting to separated servers High level overview of installation process Completing the installation administration Testing the complete installationConfiguring the hardware in the rack Configuring the Snmp modules in the UPS Security Alert Setting selected traps alarming Single control networkDuplicated control network Page Use the command set spanning disable Configuring the media server Clearing the ARP cache on the laptopPowering up the media server Accessing the media serverSetting up Telnet Installing Avaya Communication Manager Using the Installation Wizard Click Launch Avaya Installation Wizard Click Execute Ping Configuring the modem Testing the media server LEDs Disconnecting from the media serverConfiguring second media server Remastering the hard driveJune Translating the IPSIs Starting terminal emulationResetting the media server Inputing translationsAdding media gateways Administering the IPSIs Adding Ipsi informationTranslating the IPSIs Administering the IPSIs Enabling Ipsi duplication duplicated control network only S8700/S8710 MCSetting alarm activation level Installing the translation fileConnecting to the IPSIs Using Dhcp addressing Programming the Ipsi circuit packsUsing static addressing Setting the switch IDConnecting directly to the Ipsi Type show control interface and press Enter Verifying that IPSIs are translated LED display showing that the Ipsi has a static IP addressVerifying connectivity to media server Upgrading Ipsi firmware version if necessaryEnabling control of IPSIs Reusing a TN2312AP/BP circuit pack Verifying license statusCompleting the installation administration Verifying translationsSetting daylight savings time rules Type change daylight-savings-rules and press EnterSetting locations if necessary Verifying date and timeResolving alarms Enabling and disabling Ethernet switch portsBacking up files to the compact flash media S8710 only June Backing up files to the Pcmcia flashcard S8700 only Placing the flashcard in the media serverJune To Inads via modem Enabling alarmsTelneting to media server To Inads via SnmpRegistering the system Installing the media gateways June Testing the media server installation Testing the TN2312BP Ipsi circuit packTesting the license file Sample Ipsi 01A test results screen-pageLED indicators S8700 Media Server LEDsTesting the media server LEDs Interpreting the test results S8710 Media Server LEDs DiscLEDs on back panel of S8710 Media Server Avaya Ethernet switch LEDs LEDs on Avaya P333T Ethernet switchUninterruptible power supply LEDs Ipsi LEDsTN2312BP circuit pack faceplate LED display on the Ipsi circuit pack-static address LED display indicating connectivity status-DHCP address Accessing the media server Connecting to the media server directlyCadlsrvr KLC Cadlsrv2 KLC Connecting to the media server remotely over the network Connecting to the media server remotely over a modemSetting up a dial-up connection Accessing the Maintenance Web Interface Dialing up to the media serverFinding the active media server IP address Using the command line interface LoginsNetwork configuration Browser settings Connecting directly to the media serverConnecting remotely through the network Troubleshooting an installation Installing the media server hardwareConfiguring the media server hardware DhcpInstalling the license and Avaya authentication files Troubleshooting an installation Index IndexJune Using Dhcp IP address, 50 using this documentation June

S8710 specifications

The Avaya S8710 is a robust and scalable communication platform designed to cater to the needs of medium to large enterprises. As a part of Avaya's portfolio, this solution is built to provide enhanced call control, unified communications, and superior customer service, all while ensuring flexibility and reliability.

One of its standout features is its support for VoIP (Voice over Internet Protocol), which allows businesses to leverage their existing data networks for voice communications. This feature not only reduces costs associated with traditional telephony but also ensures higher quality calls and advanced functionalities. It integrates seamlessly with various telecommunications technologies, making it an essential tool for modern enterprises.

The S8710's architecture is highly modular, allowing businesses to scale their operations easily. This modularity enables organizations to start with a basic configuration and expand as their needs grow. The system can support thousands of voice channels, making it ideal for large organizations with high call volumes.

Another significant characteristic of the Avaya S8710 is its support for a variety of endpoints, including traditional digital phones, analog devices, and advanced IP phones. This flexibility allows enterprises to implement a mix of old and new technologies as they transition to a more modern communication infrastructure. Additionally, the platform offers advanced features such as integrated conferencing, automatic call distribution, call prioritization, and intelligent call routing, enhancing the overall customer experience.

The S8710 also supports various deployment options including premise-based, cloud-based, or hybrid setups, providing organizations with the capacity to choose the model that best fits their operational needs. The system’s reliability is further strengthened by its built-in redundancy and failover capabilities, ensuring minimal disruptions during service outages.

For further enhancements, the Avaya S8710 integrates with Avaya's unified communications solutions, allowing for the convergence of voice, video, and data services. This integration facilitates better collaboration among teams, improved decision-making processes, and higher productivity levels.

In summary, the Avaya S8710 offers a comprehensive, adaptable communication solution for businesses looking to modernize their telecommunications infrastructure. Its rich set of features, robust technologies, and flexible deployment options make it a premier choice for organizations aiming for operational efficiency and enhanced customer engagement.
Top Page Image Contents