Avaya S8710 manual Powering up the media server, Accessing the media server, Setting up Telnet

Page 34

Configuring the media server

Powering up the media server

1S8700: Connect the AC power cord to media server 1 and to UPS 1 to power it up.

S8710: Connect the AC power cord to media server 1 and to UPS 1. Press the Power button on the front to power it up.

Accessing the media server

NOTE:

You must place the CD in the drive immediately.

1Connect the laptop to the services port (port 2 [Eth1]) on the back of the media server using a crossconnect cable.

2Place the CD with Avaya Communication Manager in the CD-ROM drive on the media server.

3Wait at least 3 minutes after powering up before starting a Telnet session to access the information on the CD.

Setting up Telnet

NOTE:

Use a telnet session to access the information on the CD.

The Microsoft Telnet application may be set to send a carriage return (CR) and line feed (LF) each time you press Enter. The installation program sees this as 2 key presses. If running Windows 2000/XP, you need to correct this before you copy the Remaster Program to the hard drive.

1Click Start > Run to open the Run dialog box.

2Type telnet and press Enter to open a Microsoft Telnet session.

3Type display and press Enter to see the current settings. If message says

Sending only CR

then close the dialog box.

If message says

Sending both CR & LF

then continue with step 4.

4Type unset crlf and press Enter.

5Type display and press Enter to verify that the settings changed. The message says

Sending only CR

6Close the dialog box.

34	Installing and Configuring the Avaya S8700 or S8710 Media Server
	June 2004

Image 34

Contents 6HUYHU Copyright 2004, Avaya Inc All Rights Reserved SOC/REN Installation and Repairs Contents Configuring the hardware in the rack Connecting to the IPSIs Accessing the media server About This Documentation Using this documentationAudience General Physical dimensionsConventions TerminologyCommands Downloading this book and updates from the Web Downloading this documentationSafety labels and security alert labels Related resourcesSending us comments Technical assistanceTrademarks Within the USIntroduction Pre-installation information Before you go on siteDownloading license and Avaya authentication files Equipment specifications Before you start the installationEquipment specifications Required hardware Documentation Connecting to the customer’s network Figure notes Connecting to collocated servers Connecting the USB modemsConnecting to separated servers High level overview of installation process Completing the installation administration Testing the complete installationConfiguring the hardware in the rack Configuring the Snmp modules in the UPS Security Alert Single control network Setting selected traps alarmingDuplicated control network Page Use the command set spanning disable Configuring the media server Clearing the ARP cache on the laptopAccessing the media server Powering up the media serverSetting up Telnet Installing Avaya Communication Manager Using the Installation Wizard Click Launch Avaya Installation Wizard Click Execute Ping Configuring the modem Testing the media server LEDs Disconnecting from the media serverConfiguring second media server Remastering the hard driveJune Translating the IPSIs Starting terminal emulationInputing translations Resetting the media serverAdding media gateways Administering the IPSIs Adding Ipsi informationTranslating the IPSIs Administering the IPSIs Enabling Ipsi duplication duplicated control network only S8700/S8710 MCSetting alarm activation level Installing the translation fileConnecting to the IPSIs Using Dhcp addressing Programming the Ipsi circuit packsUsing static addressing Setting the switch IDConnecting directly to the Ipsi Type show control interface and press Enter Verifying that IPSIs are translated LED display showing that the Ipsi has a static IP addressUpgrading Ipsi firmware version if necessary Verifying connectivity to media serverEnabling control of IPSIs Reusing a TN2312AP/BP circuit pack Verifying license statusCompleting the installation administration Verifying translationsSetting daylight savings time rules Type change daylight-savings-rules and press EnterSetting locations if necessary Verifying date and timeResolving alarms Enabling and disabling Ethernet switch portsBacking up files to the compact flash media S8710 only June Backing up files to the Pcmcia flashcard S8700 only Placing the flashcard in the media serverJune To Inads via modem Enabling alarmsTelneting to media server To Inads via SnmpRegistering the system Installing the media gateways June Testing the media server installation Testing the TN2312BP Ipsi circuit packTesting the license file Sample Ipsi 01A test results screen-pageLED indicators S8700 Media Server LEDsTesting the media server LEDs Interpreting the test results S8710 Media Server LEDs DiscLEDs on back panel of S8710 Media Server Avaya Ethernet switch LEDs LEDs on Avaya P333T Ethernet switchUninterruptible power supply LEDs Ipsi LEDsTN2312BP circuit pack faceplate LED display on the Ipsi circuit pack-static address LED display indicating connectivity status-DHCP address Accessing the media server Connecting to the media server directlyCadlsrvr KLC Cadlsrv2 KLC Connecting to the media server remotely over a modem Connecting to the media server remotely over the networkSetting up a dial-up connection Dialing up to the media server Accessing the Maintenance Web InterfaceFinding the active media server IP address Using the command line interface LoginsNetwork configuration Connecting directly to the media server Browser settingsConnecting remotely through the network Troubleshooting an installation Installing the media server hardwareConfiguring the media server hardware DhcpInstalling the license and Avaya authentication files Troubleshooting an installation Index IndexJune Using Dhcp IP address, 50 using this documentation June