Sony DFS-700P, BKDF- 702, 702P Control From the BVE-600, Control From the PVE-500, On the BVE-600

1-60		Control From the PVE-500
		Procedure
				To perform A/B roll editing by controlling the DFS-700/700P from the
				PVE-500, use the following procedure.
				Read this in conjunction with the PVE-500 Operating Instructions.
				1 On the PVE-500, press the A/B button, turning it on.
				2 On the PVE-500, select the FROM source and TO source.
					The FROM source corresponds to the background on the DFS-700/
					700P, and the TO source corresponds to the foreground.
				3 Set the IN and OUT points for the FROM source, the TO source, and
					the recorder, in any order.
					Note
					Because the DFS-700/700P has a built-in frame synchronizer, output
					of player VCR edit points set on the PVE-500 is delayed by 1 frame,
					so that recording begins with the previous frame. However, recorder
					edit points are not delayed.
				4 On the PVE-500, press the TRANS button, turning it on, and set the
					transition duration.
				5 On the DFS-700/700P, select the effect and make other settings as
					required.
					Note that the transition duration set on the PVE-500 takes priority.
				6 Conduct a preview as required and execute the edit.
					The edit is recorded as shown below.
	Chapter5
	Control Control	Recorder and FROM		FROM source OUT point		Recorder and TO
		source IN points		TO source IN point		source OUT points
	From Units
	Editing	Recorder video	Player A video		Player B video	Recorder video

Transition duration

DFS-700/700P 5-4 Chapter 5 Control From Editing Control Units

Control From the BVE-600

You can combine the DFS-700/700P with a BVE-600 Editing Control Unit to carry out A/B roll editing using two players and one recorder.

The BVE-600 controls the DFS-700/700P using the GPI trigger signals T1 and T2.

Notes

• You cannot use the built-in switcher of the BVE-600 (BKE-611/612/621/ 622) when you are using the DFS-700/700P.

• For details of preread editing, see the section “Preread Editing” (page 5-

14).

Preparations

Make the following preparations to control the DFS-700/700P from the

BVE-600.

For details of operation, refer to the BVE-600 Operating Instructions.

On the DFS-700/700P

• In page 1 of the setup menu, set F3(PORTS) to “BVE-600”.

• Press the EDITOR button on the control panel, turning it on. (This button is lit when the DFS-700/700P is powered on.)

On the recorder VCR

• Set the recorder VCR so that it enters PB (playback) mode when stopped. (If the VCR has a selector for PB or PB/EE, set it to PB.)

• If the VCR has a built-in TBC, set the VCR to DELAYED SYNC mode.
On the BVE-600
On the rear panel, set S502 DIP switch 3 and S503 DIP switch 2 to the
lower position (OFF), and power the BVE-600 on again.	Chapter
When the unit is shipped from the factory, all DIP switches are set to the
upper position (ON).
	5
	Control Control
Notes
	From Units
• To display the background image during or after a transition, press an
appropriate BACKGROUND bus button on the DFS-700/700P.	Editing
• Because the DFS-700/700P has a built-in frame synchronizer, output of
player VCR edit points set on the BVE-600 is delayed by 1 frame, so that
recording begins with the previous frame. However, recorder edit points
are not delayed. For example, if the IN point of the player VCR is set to
00:00:10:15, actual recording begins from 00:00:10:14.
• The timing of the start of a transition is delayed by two frames from the
BVE-600 setting.

Chapter 5 Control From Editing Control Units 5-5