Pelco C3463M-B manual Back Exit Zones Zone Number, Edit Zone Label, Clear Zone Back Exit

Page 40

ZONES

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS> ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA> <MOTION>

<AUTO TRACKING> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

ZONES

ZONE NUMBER

* * * ZONE NOT DEFINED * * *

<EDIT ZONE LABEL>

<EDIT ZONE>

ZONE ENABLED ZONE BLANKING

<CLEAR ZONE>

BACK

EXIT

A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. Spectra IV dome systems are capable of eight zones, each with a 20-character label.

To configure a zone:

1.Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open, and the cursor moves to the right.

2.Move the joystick up or down to view selections. Press Iris Open to enter selection.

3.Use the joystick to position the cursor beside EDIT ZONE.

4.Press Iris Open. The Zone configuration window appears.

5.Follow the directions displayed on the monitor. After the left and right limit stops are set, the Zones menu reappears with the ZONE ENABLED option set to YES.

To edit a zone label:

1.Use the joystick to position the cursor beside EDIT ZONE LABEL.

2.Press Iris Open. The following information appears:

LABEL FOR ZONE

ZONE NUMBER ------

1234567890	OK
ABCDEFGHIJ	CANCEL
KLMNOPQRST
UVWXYZ.,-/	BACKSPACE
abcdefghij	SPACE
klmnopqrst
uvwxyz*;:

3.Use the joystick to position the cursor beside a character. Press Iris Open to enter selection. To clear a character, position the cursor beside BACKSPACE, and then press Iris Open.

4.When the label is completed, move the cursor to OK. Press Iris Open to return to the Zones menu.

To disable a zone (a zone is enabled automatically when it is configured) or to blank a zone:

1.Move the cursor beside ZONE ENABLED or ZONE BLANKING.

2.Press Iris Open. The cursor moves to the right.

3.Move the joystick up or down to view selections. Press Iris Open to enter selection.

To clear a zone:

1.Use the joystick to position the cursor beside CLEAR ZONE.

2.Press Iris Open. Follow the instructions on the screen.

*This setting applies to Pressurized Spectra IV dome systems only.

40	C3463M-B (2/11)

Image 40

Contents Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Installation Switch SettingsSW2 Switches 4 and 5 Serial Port Settings SW2 Switches 6 to 8 Baud SettingsDome Drive AddressOperation Quick Configuration GuideQuick Operation Guide Preset 95 Accessing Main Menu Extended Coaxitron or RS-485 ModeDigital Sentry System Software Endura WorkstationDigital Sentry DS Controlpoint 23X LowLight Day/Night Menu Tree Dome Settings Line Sync PresetsAlarms Password Edit the PasswordAlert Current Reading Clear Password 27X LowLight Day/Night Menu TreeLabel Position Patterns ZonesPower UP Line Sync Presets Motion Detection Event Edit Event35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Language Reset Camera Cycle Camera Power Reboot System ExitSpectra Language DIP Switch Information System InformationExit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit Title Text Save and Exit Cancel Help Label PositionsEvent Alert MessageDome Settings CameraType of Lighting Auto FocusZoom Limit Zoom SpeedLOW Light Limit PT Focus LockAuto IR Level IR CUT FilterLow Light Focus Advanced Camera Settings Shutter SpeedAGC Limit Auto IrisAuto Sharpness Auto White BalanceBacklight Compensation Electronic Image StabilizationOFF Low lux noise reduction is disabled LOW LUX Noise ReductionVideo Level Field AlignMotion Settings LOW Light SharpnessMinimum Focus Distance Auto FlipPreset Freeze Frame Park TimeScan Speed Limit StopsPower UP Start Time Line Sync Zoom Presets Lost Action Auto TrackingAzimuth Zero Auto TrackingDisplay Setup SensitivityStart Time ZoomPower UP Action Power UPBack Exit Power UP Power UP Action Presets Table C. Stored Presets by Back Box ModelBack Exit Line Sync Line Sync Phase Back Exit Presets Preset NumberPreset 83 to 87 Reserved Preset 92 to 93 Scan limit stops Preset 94 ReservedPreset 95 Select main configuration menu Preset 96 Stop a scanAbcdefghij Cancel Klmnopqrst Uvwxyz Label for Preset Preset NumberSpace Motion Detection Enable Motion DetectionEdit Detection Areas Edit Schedule Activate Aux CommandAux Time Back Exit Patterns PatternsBack Exit Zones Back Exit Zones Zone NumberEdit Zone Label Clear Zone Back ExitWindow Blanking Enable Window Reverse Clear Window Back ExitTo set a window blanking area Reverse DisabledClear Window Blank All Above Blank All Below Blank ALL ABOVE/BLANK ALL belowBlanked Area Alarms C3463M-B 2/11 AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text Alert RepeatACK Action System Condition Alert MessageReset Alert None default Not activatedActivate AUX Current ReadingPassword Back Exit PasswordEnable Password Edit Password Back Abcdefghij Cancel Klmnopqrst Exit UvwxyzClock Follow the instructions in for Fixed DATE, adding Week Event Event TypeBack Exit Event Event Type Event Label HolidayEdit Event Label Event LabelEdit Event Clear Event List EventHoliday Edit HolidayClear Holiday List HolidaysEdit Holiday Occurrence Month January DAY Back ExitScheduled Events Example Preset Weekend 1100 AM Sat-SunUse this page to record scheduled events Reset, Cycle Power, Reboot Reset CameraCycle Camera Power Reboot SystemSoftware/Language File Upload Maintenance Specifications Signal Format23X Models Zoom Speed 4.2/5.8 seconds Horizontal Angle of View27X Models DD42735X Models DD4CBW35Table F. Switch Settings for SW1 Pelco P-Type Control AppendixTable G. Switch Settings for SW1 Pelco D-Type Control 1 Spectra Switch Setting AddressTable G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information