Pelco C3463M-B manual Reverse, Clear Window, Disabled

Page 42

•Set windows are not visible when editing a new window location.

Disabled

Enabled

Figure 6. Window Blanking

6.The blanked area can be configured to turn on or off at a specified zoom point. To set the zoom point:

a.Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press Iris Open.

b.Zoom in to the point where you want window blanking to turn on. Press Iris Open to set the zoom point.

NOTES:

•Since the area is already blanked out, it may be difficult to determine when you want window blanking to turn on. Reverse the window before setting the zoom point. When finished reverse the window again to blank out the area.

•Increase the size of the window if any part of the blanked area is revealed during PTZ operations.

EDIT SCHEDULE

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 53) with the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also, the Holiday feature cannot be accessed from the Edit Schedule menu.

For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on page 54.

REVERSE

A blanked out area can be reversed to make it visible and the areas on both sides of it not visible. The areas above and below the blanking area remain visible. Reversing the window a second time will return it to its original condition.

CLEAR WINDOW

All areas that have been set for window blanking are cleared.

42	C3463M-B (2/11)

Image 42

Contents Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Installation Switch SettingsSW2 Switches 4 and 5 Serial Port Settings SW2 Switches 6 to 8 Baud SettingsDome Drive AddressQuick Configuration Guide OperationQuick Operation Guide Preset 95 Accessing Main Menu Extended Coaxitron or RS-485 ModeEndura Workstation Digital Sentry System SoftwareDigital Sentry DS Controlpoint 23X LowLight Day/Night Menu Tree Alarms Dome SettingsLine Sync Presets Password Edit the PasswordLabel Position Alert Current Reading Clear Password27X LowLight Day/Night Menu Tree Patterns ZonesPower UP Line Sync Presets Motion Detection Event Edit Event35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Reset Camera Cycle Camera Power Reboot System Exit LanguageSpectra Language DIP Switch Information System InformationDisplay Setup Exit Display Setup Preset LabelRestore Factory Defaults Back Exit Event Title Text Save and Exit Cancel HelpLabel Positions Alert MessageType of Lighting Dome SettingsCamera Auto FocusLOW Light Limit Zoom LimitZoom Speed PT Focus LockIR CUT Filter Auto IR LevelLow Light Focus AGC Limit Advanced Camera SettingsShutter Speed Auto IrisBacklight Compensation Auto SharpnessAuto White Balance Electronic Image StabilizationVideo Level OFF Low lux noise reduction is disabledLOW LUX Noise Reduction Field AlignMinimum Focus Distance Motion SettingsLOW Light Sharpness Auto FlipScan Speed Preset Freeze FramePark Time Limit StopsAzimuth Zero Power UP Start Time Line Sync Zoom Presets Lost ActionAuto Tracking Auto TrackingStart Time Display SetupSensitivity ZoomPower UP Power UP ActionBack Exit Power UP Power UP Action Back Exit Line Sync Line Sync Phase PresetsTable C. Stored Presets by Back Box Model Back Exit Presets Preset NumberPreset 95 Select main configuration menu Preset 83 to 87 ReservedPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 96 Stop a scanLabel for Preset Preset Number Abcdefghij Cancel Klmnopqrst UvwxyzSpace Enable Motion Detection Motion DetectionEdit Detection Areas Activate Aux Command Edit ScheduleAux Time Patterns Back Exit PatternsBack Exit Edit Zone Label ZonesBack Exit Zones Zone Number Clear Zone Back ExitEnable Window Reverse Clear Window Back Exit Window BlankingTo set a window blanking area Disabled ReverseClear Window Blank ALL ABOVE/BLANK ALL below Blank All Above Blank All BelowBlanked Area Alarms C3463M-B 2/11 Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 Mode AUXDwell Time Secs Edit Schedule Back Exit Title Text Back Exit Title TextEdit Title Text ACK Action AlertRepeat System Condition Alert MessageActivate AUX Reset AlertNone default Not activated Current ReadingEnable Password Edit Password PasswordBack Exit Password Back Abcdefghij Cancel Klmnopqrst Exit UvwxyzClock Follow the instructions in for Fixed DATE, adding Week Back Exit Event Event Type Event Label EventEvent Type HolidayEvent Label Edit Event LabelEdit Event Holiday Clear EventList Event Edit HolidayEdit Holiday Occurrence Clear HolidayList Holidays Month January DAY Back ExitExample Preset Weekend 1100 AM Sat-Sun Scheduled EventsUse this page to record scheduled events Cycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot SystemSoftware/Language File Upload Maintenance 23X Models SpecificationsSignal Format Zoom Speed 4.2/5.8 seconds Horizontal Angle of View27X Models DD42735X Models DD4CBW35Table F. Switch Settings for SW1 Pelco P-Type Control AppendixTable G. Switch Settings for SW1 Pelco D-Type Control 1 Spectra Switch Setting AddressTable G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information